Gcode G代码详解打印版.pdf

下载文档

43
0
约3万字
约 13页
2020-08-12 发布于广东
举报
版权申诉
保障服务

Gcode G代码详解打印版.pdf

1、本文档共13页，可阅读全部内容。
2、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。
3、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
4、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。

学海无涯 reprap wiki 上面的Gcode 说明 G-code From RepRapWiki (Redirected from Gcode) Jump to: navigation, search Contents [hide] 1 Introduction 2 RepRap G Code Fields 3 Comments 4 Individual commands 4.1 Checking 4.1.1 N and * 4.2 Buffered G Commands 4.2.1 G0: Rapid move 4.2.2 G1: Controlled move 4.2.3 G28: Move to Origin 4.3 Unbuffered G commands 4.3.1 G4: Dwell 4.3.2 G20: Set Units to Inches 4.3.3 G21: Set Units to Millimeters 4.3.4 G90: Set to Absolute Positioning 4.3.5 G91: Set to Relative Positioning 4.3.6 G92: Set Position 4.4 Unbuffered M and T commands 4.4.1 M0: Stop 4.4.2 M17: Enable/Power all stepper motors 4.4.3 M18: Disable all stepper motors 4.4.4 M20: List SD card 4.4.5 M21: Initialise SD card 4.4.6 M22: Release SD card 4.4.7 M23: Select SD file 4.4.8 M24: Start/resume SD print 4.4.9 M25: Pause SD print 4.4.10 M26: Set SD position 4.4.11 M27: Report SD print status 4.4.12 M28: Begin write to SD card 4.4.13 M29: Stop writing to SD card 4.4.14 M40: Eject 4.4.15 M41: Loop 4.4.16 M42: Stop on material exhausted 4.4.17 M43: Stand by on material exhausted 4.4.18 M80: ATX Power On 4.4.19 M81: ATX Power Off 4.4.20 M84: Stop idle hold 1 学海无涯 4.4.21 M92: Set axis_steps_per_unit 4.4.22 M101 Turn extruder 1 on Forward 4.4.23 M102 Turn extruder 1 on Reverse 4.4.24 M103 Turn all extruders off 4.4.25 M104: Set Extruder Temperature (Fast) 4.4.26 M105: Get Extruder Temperature 4.4.27 M106: Fan On 4.4.28 M107: Fan Off 4.4.29 M108: Set Extruder Speed 4.4.30 M109: Set Extruder Temperature 4.4.31 M110: Set Current Line Number 4.4.32 M111: Set Debug Level 4.4.33 M112: Emergency Stop 4.4.34 M113: Set Extruder PWM 4.4.35 M114: Get Current Position 4.4.36 M115: Get Firmware Version and Capabilities 4.4.37 M116: Wait 4.4.38 M117: Get Zero Position 4.4.