整理Gcode G代码详解.pptxVIP

下载本文档

109
0
约2.24万字
约 18页
2021-01-23 发布于广东
举报
版权申诉

整理Gcode G代码详解.pptx

1、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。。
2、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
3、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。
4、该文档为VIP文档，如果想要下载，成为VIP会员后，下载免费。
5、成为VIP后，下载本文档将扣除1次下载权益。下载后，不支持退款、换文档。如有疑问请联系我们。
6、成为VIP后，您将拥有八大权益，权益包括：VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
7、VIP文档为合作方或网友上传，每下载1次，网站将根据用户上传文档的质量评分、类型等，对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档

reprap wiki 上面的 Gcode 说明 G-code From RepRapWiki (Redirected from Gcode) Jump to: navigation, search Contents [hide] Introduction RepRap G Code Fields 3 Comments Individual commands Checking N and * Buffered G Commands G0: Rapid move G1: Controlled move G28: Move to Origin Unbuffered G commands G4: Dwell G20: Set Units to Inches G21: Set Units to Millimeters G90: Set to Absolute Positioning G91: Set to Relative Positioning G92: Set Position Unbuffered M and T commands M0: Stop M17: Enable/Power all stepper motors M18: Disable all stepper motors M20: List SD card M21: Initialise SD card M22: Release SD card M23: Select SD file M24: Start/resume SD print M25: Pause SD print M26: Set SD position M27: Report SD print status M28: Begin write to SD card M29: Stop writing to SD card M40: Eject M41: Loop M42: Stop on material exhausted M43: Stand by on material exhausted M80: ATX Power On M81: ATX Power Off;M84: Stop idle hold M92: Set axis_steps_per_unit M101 Turn extruder 1 on Forward M102 Turn extruder 1 on Reverse M103 Turn all extruders off M104: Set Extruder Temperature (Fast) M105: Get Extruder Temperature M106: Fan On M107: Fan Off M108: Set Extruder Speed M109: Set Extruder Temperature M110: Set Current Line Number M111: Set Debug Level M112: Emergency Stop M113: Set Extruder PWM M114: Get Current Position M115: Get Firmware Version and Capabilities M116: Wait M117: Get Zero Position M118: Negotiate Features M119: Get Endstop Status M126: Open Valve M127: Close Valve M128: Extruder Pressure PWM M129: Extruder pressure off M140: Bed Temperature (Fast) M141: Chamber Temperature (Fast) M142: Holding Pressure M143: Maximum hot-end temperature M160: Number of mixed materials M203: Record Z adjustment M226: Gcode Initiated Pause M227: Enable Automatic Reverse and Prime M228: Disable Automatic Reverse and Prime M229: Enable Automatic Reverse and Prime M230: Disable / Enable Wait for Temperature Change M240: Start conveyor belt motor M241: Stop conveyor belt motor M245: