《射频通信电路》陈邦媛著课后答案超详细.docxVIP

第一章 1-1 1 S = = ?16dB = 0.158 0.6 × 2 1 + ( × 66.67)2 10 f = f0 ± 100kHz 及 f0 = 640kHz 代入 得 Q=20 BW3dB = Qf0 = 640200 = 32kHz 1-2 1 1 （1） L = = = 4.53μH ω02 C (2π ×107 )2 × 56 ×10?12 Q0 = f0 = 10 = 66.67 0.15 BW3dB S = 1 = 1 = 0.124 = ?18.13dB 2( f ? f0 ) 2 0.6 × 2 2 1 1 + × 66.67 + Q0 f0 10 （2）当 BW3dB = 300kHz 时 Qe = f0 = 10 = 33.33 BW3dB 0.3 回路谐振电导 Ge = 1 = ω0C = 2π ×107 × 56 ×10?12 = 10.55 ×10?5 （s） ρQe 33.33 Qe 回路空载谐振电导 G0 = 1 = ω0C = 2π ×107 × 56 ×10?12 = 5.27 ×10?5 （s） ρQ0 66.67 Q0 并联电导 = Ge ? G0 = (10.55 ? 5.27) ×10?5 = 5.28 ×10?5 （s） R = 1 1 = 18.9K? 并联电阻 G = 5.28 ×10?5 1-3 L2 L3 1 2 L1 = = 2.06μH (2πf )2 C v1 C2 C3 L2 = 1 = 2.74 μH L1 C1 (2πf2 )2 C2 v3 2’ 1 L3 = (2πf31)2 C3 = 0.68μH 1-4 x f0 f f0 = 2π 1LC x f1 f2 f (c) f1 = 1 2π C(L1 + L2 ) f2 = 2π 1CL1 1-5 由于回路为高 Q，所以回路谐振频率  x f0 f f0 = 2π 1LC x f1 f2 f f1 = 2π 1LC2 f2 = 1 2π L C1C2 C + C 2 1 f0 ≈ 1 = 1 = 465.5kHz 2π 2π 300 ×10?12 × 390 ×10?6 LC 回路的损耗电阻 = ω0 L = 2π × 465.5 ×103 × 390 ×10?6 = 11.4? Q0100 回路的谐振阻抗 RP = r(1 + Q02 ) = 114K? 考虑信号源内阻及负载后回路的总谐振阻抗为 2 RΣ = RS || RP || RL = 42K? 回路的有载 Q 值为 Qe = RΣ = 42 ×10 3 = 37 2πf0 L ρ 通频带 BW3dB = f0 = 465.5 = 12.56kHz Qe 37 在 ?f = 10kHz 处的选择性为： S = 1 = 1 = 0.532 → ?5.47dB 2?f 2 20 2 1 + 1 + 37 × Qe f0 465.5 1-6 ρ = 1 1 = 159? 回路特性阻抗 RP = ρQ = 159 ×100 = 15.9k? 回路谐振阻抗 P 2 1 P 2 由 = + 可求得 P2 = 0.336 RL RP RS RS 12.8 信号源内阻 RS 折合到回路两端为： RS = = = 20k? P 2 (0.8)2 R 1 负载电阻 RL 折合到回路两端为： RL = L = 1 = 8.86k? P 2 (0.336)2 2 回路总谐振阻抗 RΣ 为 1 = 1 + 1 + 1 = 1 + 1 + 1 = 0.0629 + 0.05 + 0.112 = 0.226ms RΣ RP RS RL 15.9 20 8.86 即 RΣ = 4.43k? 回路有载 Q 值为 Qe = RΣ = 4.43 ×103 = 27.8 ρ 159 回路的通频常 BW3dB = f0 = 10 ×106 = 0.359MHz Qe 27.8 1-7 由于 BW3dB = f 0 所以回路有载 Qe = f 0 = 10 6 = 50 Qe BW3dB 20 ×103 回路谐振时的总电导为 GΣ = 1 = 1 = 0.02 ms（即RΣ = 50 K?) ω0 LQe 2π ×10 6 ×159 ×10 ?6 × 50 3 回路的空载电导为 G p = 1 = 0.01ms （即RP = 100 K ） ω0 LQ0 信号源内阻折合到回路两端的电导值为 GS = GΣ ? G p = 0.01ms 由于GS = P 2GS ，所以电容接入系数为： P 2 = GS = 0.01×10?3 = 0.01 ? P = 0.1 GS 10 ?3 1 1 回路总电容 1 ∵接入系数 P = ωC2 = C 所示