轮机船东代表监造工作.docxVIP

轮机船东代表监造工作 轮机船东代表监造工作 68主机燃油泄放管、燃油仓的液位计及泄放管应加伴行管 导缆在安装滚轮之前轴的清洁要报验；安装后加注油脂；交船前要检查转动是69 否灵活 坞内工程：轴系跳动量、下沉量、保护罩及鱼网刀安装间隙；舵承间隙；舵叶70检测孔盖安装；水下检测；艏侧推器、螺旋浆浆叶清洁干净；吹污；海底门拉 放及内清洁； 71试航前检查克令吊、物料吊、救助艇吊、油管吊的绑扎功能72辅机试验前转子端应清洁报验再动机 73货仓抽污试验污水井内的管子、吸入滤网安装要检查报验74电工间应加通风管 75空调机房的新风吸入管应加泄放塞 76主机燃油试验台要效用；排气阀研磨台要效用报验77机舱所有压力正常运行范围要标识 冰库库房内的风机的安装时要检查，确保足够的维修空间；检查冰库的门正常78 开关功能 79克令吊起重柱体内的泄放管要安装80用拉绳检查系泊设备安装状态 81所有燃、柴、滑油管系及燃油油仓等安装的温度计应有保护套82试航期间重点测量主机排烟管的背压 83全船各仓室风机的各通风口的出风情况要报验 84油水仓室密性之前：根据开孔图检查所有开孔是否完成 压载仓内的各种管系螺栓应用不锈钢，检查时重点关注；压载管上的膨胀接85 头固定螺栓是否拆除 86透气管、泄放管、溢流管、污水管安装时应有斜度87船厂提供给船东关于管子制作密性的试验清单,p:{h:17.298,w:361.296,x:178.23,y:701.565,z:5148},ps:null,s:{letter-spacing:0.068},t:word,r:[4]},{c:{ix:0,iy:36163,iw:2,ih:2},p:{h:2,opacity:1,rotate:0,w:1.439,x:126.216,x0:126.216,x1:126.216,x2:127.656,x3:127.656,y:696.885,y0:698.325,y1:696.885,y2:696.885,y3:698.325,z:5149},ps:null,s:{pic_file:/home/iknow/conv//data//bdef//201*87002//201*87002_4_5149.png},t:pic},{c:{ix:0,iy:36170,iw:5,ih:2},p:{h:2,opacity:1,rotate:0,w:2.879,x:127.656,x0:127.656,x1:127.656,x2:130.536,x3:130.536,y:696.885,y0:698.325,y1:696.885,y2:696.885,y3:698.325,z:5150},ps:null,s:{pic_file:/home/iknow/conv//data//bdef//201*87002//201*87002_4_5150.png},t:pic},{c:{ix:0,iy:36177,iw:5,ih:2},p:{h:2,opacity:1,rotate:0,w:2.879,x:130.536,x0:130.536,x1:130.536,x2:133.416,x3:133.416,y:696.885,y0:698.325,y1:696.885,y2:696.885,y3:698.325,z:5151},ps:null,s:{pic_file:/home/iknow/conv//data//bdef//201*87002//201*87002_4_5151.png},t:pic},{c:{ix:0,iy:36184,iw:5,ih:2},p:{h:2,opacity:1,rotate:0,w:2.879,x:133.416,x0:133.416,x1:133.416,x2:136.296,x3:136.296,y:696.885,y0:698.325,y1:696.885,y2:696.885,y3:698.325,z:5152},ps:null,s:{pic_file:/home/iknow/conv//data//bdef//201*87002//201*87002_4_5152.png},t:pic},{c:{ix:0,iy:36191,iw:5,ih:2},p:{h:2,opacity:1,rotate:0,w:2.879,x:136.296,x0:136.296,x1:136.296,x2:139.176,x3:139.176,y:696.885,y0:698.325,y1:696.885,y2:696.885,y3:698.325,z:5153},ps:null,s:{pic_file:/home/iknow/conv//data//bdef//201*87002//201*87002