电机的拆卸和装配流程（PPT31页).pptxVIP

三相异步电机的拆装维护（三）电机的拆解 Motor’s dismantling1、准备工作 Readya、确认说明书 check manual设备铭牌、型号、零件清单、标准件规格、组装图、维护注意事项nameplate, model, parts list, stand parts, assembly drawing, attention注意：从组装图可以分析出这台设备正确的拆解顺序.Attention: Know correct sequence by reading assembly drawing.b、工具的准备 prepare tools内六角扳手、棘轮扳手、呆扳手、延长杆、套筒、铁/胶锤、撬棍等 hex wrench, ratchet wrench, solid wrench, extension rod, sleeve wrench, hammer, crowbar, etc.注意：工具准备应以常用工具为主，取用方便的其他工具，用时取出即可！Attention：ready common toolsc、辅助器材准备工作台、吸油纸及垃圾桶、木方、塑料盒workbench, crane, oil-absorbing sheet, trashcan, wood, plastic boxd、劳保用品的准备工作服/围裙、防滑手套、薄手套、安全鞋labour suit, slip-proof glove, mitten, safety shoee、切断能量源关停管道阀门关停电力关停压缩空气等close pipeline valvepower offcompressed air off注意：正确执行LOTO程序！Attetion：Execute LOTO exactlyf、设备清洁去除设备表面污物，油污、灰尘等clean sewage, oil, dust on the equipment surface2、执行拆解 Dismantlinga、拆除前标记位置 Marking before dismantling标记接线盒盖 → 标记电机风扇罩 → 标记前端盖 mark cable cap → mark fan cap → mark front endb、电源线拆除 Remove cable拆除接线盒盖板→并确认接线图 remove cable → check wiringc、拆解后端 dismantle back end拆除电机护罩 → 标记后端盖位置 → remove fan cap → mark back end→拆除散热风扇 →松后端螺栓 → remove fan → loose back screw 电机风扇的拆除，应使用两爪拉马拉出。should using puller with two claws to remove plastic fan.d、拆解前端 dismantle front end标记轴键 → 松前端螺栓 → 撬出前端盖 → mark shaft key → loose front screw → pry front end 标记前轴承盖板 → 松轴承盖板螺栓 → 拉出前端盖 mark → loose bearing cap’s screw → pull front end out应注意轴承空位内的调整垫片的数量和厚度。pay attention to the shim in bearing position.e、拆除后端盖 remove back end 拆除后端盖 → 清点零件 remove back end → check parts 3、检查 check检查设备重要尺寸 check important dimensions 轴承孔位处的垫片厚度check thickness of the shim in bearing position检查轴上密封部位尺寸及光洁度，有无磨损迹象check dimensions and smooth of sealing position, if corrode检查密封件完好程度，有无损坏、磨花现象check seal is intact, if broken or scratch4、清洁整理 do 5S a、所有拆解下来的螺栓、圆螺母、垫片、密封件等小件零件，都已安装完毕。All dismangtled parts, have been installed. b、使用过的工具，都已擦拭干净。All tools，have been cleaned.5、本章小节 Summarize选用合适的拉马 Puller a.两爪拉马，用于保持力不大的场合，如塑料零件； Two claw puller，is used to low thrust force. b.三