（正版）ASTM Standards F 2274 - 11 (2016) 标准文档.docVIP

下载本文档

18
0
约6.02千字
约 2页
2022-02-04 发布于上海
举报
版权申诉

（正版）ASTM Standards F 2274 - 11 (2016) 标准文档.doc

1、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。。
2、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
3、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。
4、该文档为VIP文档，如果想要下载，成为VIP会员后，下载免费。
5、成为VIP后，下载本文档将扣除1次下载权益。下载后，不支持退款、换文档。如有疑问请联系我们。
6、成为VIP后，您将拥有八大权益，权益包括：VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
7、VIP文档为合作方或网友上传，每下载1次，网站将根据用户上传文档的质量评分、类型等，对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档

Designation: F2274 ? 11 (Reapproved 2016) An American National Standard Standard Speci?cation for Condition 3 Bicycle Forks1 This standard is issued under the ?xed designation F2274; the number immediately following the designation indicates the year of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A superscript epsilon (′) indicates an editorial change since the last revision or reapproval. 1. Scope 1.1 This speci?cation establishes testing requirements for qualifying designs using production forks intended for use in Condition 3 per Classi?cation F2043. 2. Referenced Documents 2.1 ASTM Standards:2 F2043 Classi?cation for Bicycle Usage F2273 Test Methods for Bicycle Forks 3. Classi?cation 3.1 Condition 3 per Classi?cation F2043. 4. Sampling and Test Specimens 4.1 Selection and Preparation of Specimens: 4.1.1 Three forks shall be randomly selected from the ?rst production lot for the fatigue plus impact test per this speci?- cation. 4.1.2 One fork shall be randomly selected for the impact test per this speci?cation. 4.1.3 One fork shall be randomly selected for both the compression and bending tests per this speci?cation. 5. Performance Requirements 5.1 Bicycle forks intended by the manufacturer to be used according to Condition 3 shall be tested per Test Methods F2273. 5.1.1 Compression Load Test: The fork shall withstand a compression load of 2800 N without any component failure, fracture or permanent deformation. Under the application of the compression load of 2800 N, the minimum clearance from the maximum tire pro?le Equipment, Playing Surfaces, and Facilitiesand is the direct responsibility of Subcommittee F08.10 on Bicycles. Current edition approved Oct. 1, 2016. Published October 2016. Originally approved in 2003. Last previous edition approved in 2011 as F2274 – 11. DOI: 10.1520/F2274-11R16. contact ASTM Customer Service at service@. For Annual Book of ASTM Stand