F7-连线指南新—中英繁.docVIP

PAGE / NUMPAGES F7 Quick　Connectｉon Guidｅ Ｃonnｅctｉon betｗeｅn F7　terminal aｎｄ power　supplｙ ?Ｆ7　ｔeｒminal ｉs ｓｈown ｉn　aｂove　ｆiｇure。 It supportｓ DC　ｐｏwer ｓｕｐｐlｙ ｏf 9—15Ｖ as　ｉｎput,　aｎｄ can ｗork imｍedｉａtｅｌy throuｇh　the direct ｃonnecｔｉｏn ｂｅtｗｅen GＮD ａnd ＋12V 。 Ｉｆ lｏck-contrｏl uｓes the　indivｉｄual power　ｓupplｙ, the　ｃuｒreｎt ｏf Ｆ7’s ｐoweｒ supｐｌy ａdapter　apｐliｅs mａtｃhing current　ｏf　500mA or oｖer； if lｏcｋ-control usｅs ｔhe sａme power supplｙ with F7，　thｅ nｏｍinal outｐut　ｃｕrｒｅnt ｏf thｅ poweｒ ａdapter　wｉll ｅxceed the worｋing ｃurrｅｎt　ｂy ovｅr 1000mA. GＮD GND +１2V Pｏwｅr ＲS232 RＸD Lock　ＣOＭ RS2３２ ＴXD Ｌocｋ NO GND Ｌock NＣ RＳ485 A GＮD RS４85 B Aｌaｒm+ GND Ａｌarm— ＤATＡ０ Buttoｎ DＡTＡ1 ＧNＤ +５V Output Beｌｌ+ Doｏr Senｓor Beｌl— ＧND 9—15VPower supply adapter + 9—15V Power supply adapter + Coｎnectｉon with door　lock F7 caｎ　sｕｐｐｏrt normａl－ｏpen and normal-ｃloｓeｄ　door　lock siｍｕltanｅｏusｌy, so lｏng as ｉｔ　iｓ ｃonneｃteｄ with the different tｅrmｉnals respｅctｉvely. Ｕsｕａlly， lock　No　teｒminaｌ dｉsｃonｎectｓ with COM teｒminaｌ, ａｎd ｔhｅy cｏｎnect when F7 outputs　thｅ unlocｋiｎｇ sigｎal　and ｒecovｅｒ　to diｓconnecｔion when ｔhe signaｌ eｎds. The　conneｃtiｏｎ　aｎd discoｎnecｔioｎ bｅtwｅｅn Lock NＣ teｒｍinal ａnｄ COM ｔｅrｍiｎal is opposｉte to aboｖe situａtｉon, tｈey cｏnnect ｕｓuaｌlｙ　and disconnect when thｅ unｌockiｎg ｓignａl iｓ ｏutput。 Dｕe　to ｔhe existencｅ of varied ｅlｅctrｉc-cｏnｔｒoｌ dooｒ　locks， ｔhｅ cｏrrｅct conｎｅction mｅtｈod　ｍusｔ bｅ cｏnfｉrmed iｎ acｃordance ｗith the　dｏor lｏck spｅｃifiｃaｔion： Lock NO ｔｅrmiｎal sｈｏuｌd be uｓed ｆoｒ the　ｌｏｃks， whicｈ ｕｎlock whｅｎ thｅ ｐｏwer　is　ｏn and lock wheｎ ｐower ｉs　oｆf； othｅrwise， tｈe Locｋ NC ｔerminａl　sｈｏｕｌd bｅ　uｓed. Taｋe the eｌeｃtｒic－coｎtrol lock，　wｈich lｏcks usuａｌly when powｅｒ ｉs oｆf,　fｏr eｘample　hereｉｎ,　ｔｏ　show ｔｈｅ conｎｅcｔion method ｂetweeｎ F７ and ｌｏcks. Ｕｓe Lｏcｋ　NC termｉｎal　ｗhen　F7 is　connｅcted with the　lｏck， which lockｓ usｕaｌlｙ ｗheｎ　power is on. Power supply Power supply adapter - 12V + GNＤ GND +１2V 　Poｗer ＲＳ2３2 RXＤ Lock COM RS232 ＴXD Ｌocｋ NO GＮD Lock　ＮＣ RＳ485 A ＧND RS４85 B Alａrm＋ ＧND Alaｒm— DAＴA0 Buｔton