F7-连线指南新—中英繁(1).docVIP

PAGE / NUMPAGES Ｆ7　Ｑuick　Cｏnnectiｏn Gｕide Conｎeｃtion between F7 ｔｅrｍiｎaｌ ａｎｄ poｗer　sｕpply F7 ｔｅrminal is shoｗn iｎ above fｉguｒe. It　ｓupports DC　pｏweｒ suｐpｌy ｏf 9-15V　as ｉnput,　and ｃan woｒk imｍediaｔelｙ thｒouｇh　tｈe ｄirect ｃoｎneｃｔｉon beｔｗeen GND　ａnd ＋１２Ｖ 。 If lock-control　uｓｅｓ the ｉndividual pｏｗeｒ sｕpply, ｔhe　cuｒreｎt ｏf　F7’s power supply adaｐter applies maｔchｉｎg cｕｒrｅnt of　500ｍＡ ｏr　oｖer； if locｋ－control useｓ　the samｅ　poweｒ sｕpplｙ witｈ　Ｆ７， ｔhe　nｏｍiｎａｌ　ｏutpuｔ ｃｕrrent　of　ｔhe poｗeｒ ａｄaｐtｅｒ will exceed thｅ wｏrkiｎｇ cｕｒｒent by ｏｖｅr 1000mＡ.　 GＮD GND +12V 　Pｏweｒ RS２32　RＸD Lock CＯM RS232　TＸD Ｌock　NO GND Loｃk NC RＳ48５ A GNＤ ＲS4８5 B Alarm＋ GND Alａrｍ- DATA0 Bｕtｔon ＤＡＴA1 GND +5Ｖ Outｐuｔ Beｌl+ Dｏor　Sensor Beｌl- GND 9—15VPower supply adapter + 9—15V Power supply adapter + Conｎecｔion　with ｄoｏr　lｏｃk F7 can support normａl—ｏｐen ａnｄ　normａｌ—cｌｏｓeｄ　door　ｌock ｓiｍultanｅouｓlｙ， so　lonｇ as　it is connecｔeｄ ｗｉｔｈ ｔhｅ diｆfｅｒeｎｔ　termｉnals respectively. Ｕｓualｌy,　locｋ　Ｎo terｍｉnａｌ　diｓcｏnｎects wiｔh　ＣOM　tｅrminal，　and tｈeｙ connect　when F7 outｐuts the　ｕnlockｉnｇ　ｓｉgnａｌ ａnd recovｅr to discｏnnｅcｔion　ｗheｎ the　ｓignal eｎds。 Thｅ cｏnnectｉon ａｎd　dｉsconnｅcｔｉoｎ bｅtweｅn Ｌock NC terｍｉnal　anｄ　CＯＭ tｅrｍｉnal ｉs ｏpposiｔe ｔo abovｅ　situaｔｉｏｎ, they ｃonnect usuaｌly aｎd discｏnnect ｗhen ｔhe unlocking ｓｉgnａｌ ｉs ｏutｐut． Dｕe to　tｈe exiｓteｎce oｆ vａrｉed eｌecｔｒｉc—contrｏl dｏor ｌoｃks， the ｃorrｅct ｃonneｃtion　mｅthoｄ must be confirmeｄ ｉn accordance with the　ｄooｒ lock ｓpecifｉcaｔion： Lｏｃk　NＯ terminａｌ sｈｏuld be used　ｆｏr ｔｈe locks， which　unｌｏｃk ｗhｅｎ the powｅｒ　ｉs ｏn anｄ ｌoｃk wheｎ poweｒ　is off; ｏtherwiｓe，　ｔhe Ｌｏｃk　NＣ ｔｅｒminal should be used． Take ｔhe　ｅlｅctriｃ—control lock, whicｈ loｃｋs ｕsｕａｌｌy ｗｈｅn ｐowｅr is　ofｆ, for exａmple ｈereiｎ， to sｈow the coｎneｃtion　ｍetｈod beｔween F7 and lockｓ。 Ｕse Lock ＮC terminal　ｗhen Ｆ7 ｉs　connｅcｔeｄ witｈ　thｅ locｋ，　wｈicｈ ｌoｃks usually when poweｒ　is on。 Power supply Power supply adapter - 12V + GND GNＤ +12Ｖ Powｅｒ ＲS232　RＸＤ Locｋ　CＯM RS232　TXD Locｋ NO GND Lock ＮC ＲＳ4８5 A GND RS４8５ Ｂ Ａlarm+ ＧＮＤ Ａｌarm— DATA0 Button