JBT 2001.1-1999水系统 柱塞压盖 型式与尺寸(PN=31.5MPa).pdf

ICS 23.100J 20JB中华人民共和国机械行业标准JB/T2001.1—1999水系统柱塞压盖型式与尺寸Water systemPlug glandType and size(PN=31.5 MPa)1999-06-28发布2000-01-01实施国家机械工业局发布 中华人民共和国机械行业标准柱塞压盖型式与尺寸JB/T 2001.11999水系统Water systemPlug glandType and size代替JB 2001—84(PN=31.5MPa)1范围本标准规定了工作缸密封用柱塞压盖的型式与尺寸。本标准适用于公称压力31.5MPa各种工作缸密封用柱塞压盖。型式与尺寸2.1型式应符合图1的规定。一压套：2一垫片组：3一梅花垫：4一梅花压极：5—法兰：6—烯柱：7—螺母：8—烯栓图 12.2尺寸应符合图1、表1的规定。国家机械工业局1999-06-28批准2000-01-01 实施 JB/T 2001.11999表 1DN润滑孔H9/f9H9/d11d2dswXd4nXd,重量mmkgJB/T 2001.1.140601101555.34JB/T 2001.1.24565115160 5.57JB/T 2001.1.350751201656 X M20606JB/T 2001.1.45580125170256.3JB/T 2001.1.5601301756.5JB/T 2001.1.665061401908.5JB/T 2001.1.795150200650L10308.7JB/T 2001.1.8100B/T 2001.1.98010516021010.4JB/T 2001.1.101652156 X M248501 IO11.2JB/T 2001.1.111151702207012JB/T 2001.1.121202JB/T 2001.1.1310012523012.6JB/T 2001.12002601 XM14X1.520JB/T 2001.1.15150210270853512021JB/T 2001.1.1612515521527526JB/T 2001.1.1716022028026.6JB/T 2001.1.181401702302908 X 7JB/T 2001.1.1915018024030028.4JB/T 2001.1.2019025031029.8JB/T 2001.1270330154034.3954§JB/T 2001.1.2220023029035036.2JB/T 2001.1.232202503100L43.310050JB/T 2001.1.2425028034040047.25260290350410 10XM3052JB/T 2001.1.262803103704301105555JB/T 2001.1.2730033039045057JB/T 2001.1.28360430510102400M36X313065JB/T 2001.1.29110JB/T 2001.1.3038042049057070120JB/T 2001.1.3144053062020602X M14X1.5400145B/1°:42046055064012XM42X314075161490580570167 JB/T 2001.11999表1(完)DN润滑孔代H9/f9H9/d11d2dswXd4HTIh2Em重量X dsmmkgJB/T 2001.1.3450054063072080JB/T 2001.1.35520560650740211780150JB/T 2001.1.36560600690231JB/T 2001.1.3762071080016XM42X3855802070236JB/T 2001.1.38630670760850263JB/T 2001.1.3965069078087016090275JB/T 2001.1.407107508409304XM14X1.5288JB/T 2001.1.4173078087598016XM48X3180100392JB/T 2001.1.428208709651070110481JB/T 2001.1.4395011502002580900104520XM48X3115528JB/T 2001.1.440Z697010651170534JB/T 2001.1.451000105011601270220130723JB/T 2001.1.4611901300141020XM56X4135828JB/T 2001.1