JBT 7185.2-1995冲模滑动导向钢板模座 对角导柱上模座.pdf

中华人民共和国机械行业标准JB/T 7185. 2-95冲模滑动导向钢板模座对角导柱上模座生题内容与适用范围本标准规定了冲模滑动导向钢板模座对角导柱上模座的技术条件、尺寸规格、材料、热处理要求及标记。本标准适用于冲模滑动导向钢板模架引用标准JB/T7188冲模钢板模架零件技术条件GB 699优质碳素结构钢技术条件GB 700碳素结构钢GB 8845．冲模术语模座的技术条件和尺寸规格3.1技术条件按JB/T7188的规定。3. 2尺寸规格见图和表。1.6BEDK图1995—07—01实施机械工业部1995—03-—21批准46 JB/T 7185. 2--95表mmD(R?).Di(R7)凹模凋界HFS1MXtBi基本尺寸极限偏差基本尺寸极限偏差LB1002003236136313210032611363132125125200801602003296136313216020022432401201443738200324017014488250250224125224326116031z8125250324080170373816016010025032401201703?38200200250250324017017037882502654045225.1754245155M120. 025+0. 0251602803240802003?381600n2002803240120200373820028040451601904245250250100125315315280404522519042 45155M12×2540040453101904245220400280200200335404511024542452502503354516024542.4510022524542 45 15531516031533540454003354045.31024545220400404541024542453205005002502503754045160285424580225285315315375-40454245155M12X2520040031028542452204003754045+0.030+0. 030500400.5055.3902905255300500.0+0. 025+0. 025!315315425405021532542451450040045050552903405255200400250+0. 030+0. 030500500450505539034052553000M16X30630 63045050555203405255.430AT IB/T 7185. 2--95续表凹模周界D(R7)D;(R?)BiHsStSrxtL基本尺寸极展偏差基本尺寸极限偏差1:31531553050552054205255115400400530505529042052552005005005605063374434626528063063056050635044346265+0..030+0. 030380M16X304004006305063274tos620651805005006305063374$046265.280400630630.630636350450462800.6309674504.6265550M20X354材料和热处理要求4.1 材料45 钢 GB 699.模周界L×B小于400×250的滑动导向模座可用Q235-A钢GB700。4.2热处理要求45钢调质HRC26~~30.5·标记本标准规定的模座标记由下列要素组成：上模座a.b.模座的凹模周界 LXB,模座厚度 H;C.材料;本标准编号。t.示例：凹模周界 L=125 mm、B=100 mm、模座厚度 H=25 mm、材料为 45 钢的对角导柱上模座的标记如下：上模座125×100×2545 : JB/T 7185. 2