JBT 5613-2006小径定心矩形花键拉刀.pdf

ICS 25.100.25J41备案号：19082—2006中华人民共和国机械行业标准JB/T 5613--2006代替JB/T 5613—1991小径定心矩形花键拉刀Straight spline broach with minor diameter center2006-10-14 发布2007-04-01实施中华人民共和国国家发展和改革委员会发布 JB/r 5613—2006目次前言。1范围.规范性引用文件3型式尺寸3.1 型式.3.2尺寸3.3标记示例.4　技术条件。附录A（资料性附录）留磨拉刀的参考尺寸附录B（资料性附录）不留磨拉刀的参考尺寸16附录C（资料性附录）刀齿角度及刃带.20 JB/T 5613—2006表2 (续)工件参数拉刀结构尺寸b拉削花键花键规格花键槽宽倒角LbDsDsD2MD3D4长度NXdXDXB公差带CH918.25015.807.0418.20130~50 #75016.01818.2016.0020.084416X20X418.25015.807.0418.2050~80 a94018.2016.0020.08416.01810～~1861018~3073522.08418.01818.0017.808.036×18X22×50.3161630~5095020.25020.2050~8089522.08418.01820.2018.005.03010~18600≥18~3071025.08421.0212020.809.1421.006X21X25X530~50940501859518~3010.07.206X23X26X60.226.08430~5085550~8099023.0212222.8023.0010~1869018~3082528.08410.126X23 X 28 X 6308011950.36.03010~18 64018~3076530.08411.236×26× 30 × 630~～509405002125.8026.0010~1873518~3089011.286X26X 32 X 60.430~50112025255010010~1864018~3076012.216×28X 32×70.330~5094528.02128.0050~807.036109527.8010~1873589012.276×28×34 ×718~300.434.100305011208 JB/T 5613--2006表2 (续)工件参数拉刀结构尺寸b花键花键规格拉削花键檀宽倒角LbDsD6D1D2MD3NXdXDXB长度公差带cH96×28×34X750~800.47.036130034.10028.0212527.8012.2728.0010~1864518~307700.336.10013.408X 32X 36X630~5095050~801105256.03032.0252831.7532.0010~1874518~309050.438.10013.468×32×38×63080132518~3080530~～5098540.10015.138X 36×40X70.350120136036.0253235.7536.00327.03618~3094030~5011700.442.10015.188×36X42×750120163018~3080530~～509858×42× 46×80.346.10017.58501201360427542.008.03618~3094030~5011700.448.10017.638X42X48X85012016308054018~3030~509850.350.10019.308X46X50X95012046.025467518~309.0361075403012019.418X46X54X950~800.5157550.50050.4580~～120126054.12046.02550.4546.0018~3096052.00508X52X58X 100.410.03658.12052.0305051.7021.8030~5011909 JB/T 5613-2006表2 (续)拉刀结构尺寸工件参数b花键花键规格拉削花键槽宽LbD6DiD2倒角DsMD3D4NXdXDXB长度c公差带H950~8013750.458.1201 21.808×52×58× 108