JBT 7403-1994光照度计.pdf

JB中华人民共和国机械行业标准JB / T 7403-94光照度计1994--08-23 发布1995-05-01实施中华人民共和国机械工业部发布 中华人民共和国机械行业标准JB / T 7403-94光照度计1 主题内容与适用范围本标准规定了光照度计的产品分类、技术要求、试验方法、检验规则、标志、包装、运输、贮存等。本标准适用手光度头探测器为硅光电池、硅光电二极管和硒光电池的光照度计。光度头探测器为光电管的光照度计亦可参照使用。2 引用标准GB 2828 批检查计数抽样和抽样表（适用于连续批的检查）GB 2829周期检查计数抽样和抽样表（适用于生产过程稳定性的检查）JB 5517光学仪器电气防护基本安全要求ZBY 002仪器仪表运输、运输贮存基本环境条件及试验方法ZBY 003仪器仪表包装通用技术条件3产品分类3.1产品类型光照度计按读数类型分为指针式光照度计和数字式光照度计。3.2产品等级产品等级分为标准级、一级、二级、三级共四个等级。4 技术要求4.1示值误差示值误差不超过表 1 的规定。表1%级别标准级二级三级示值误差± 1.5±4.0±6.0±8.04.2光度头(光照度计的受光探头)滤光器的V()匹配误差光度头滤光器的光谱响应度对应 CIE明视觉光谱光视效率 V(入）的匹配误差不超过表 2的规定。表 2%标准级三级三 级3.05.07.09.0滤光器的V(入)匹配误差4.3 方向性响应总误差在85范围内，方向性响应总误差不超过表3的规定。1995-05-01实施机械工业部1994-08-23批准1 JB / T 7403-94附录 A色温为2856K光源的相对光谱功率分布 SA(入)及 CIE明视觉光谱光视效率V(入)表（补充件）1SA()及 V(入)表波长SA(x)V(α)波长SA(x)V(x)波长SA(x)V(x)(nm)(nm)(nm)3809.800.000051569.250.6082650165.030.107038510.900.0001.52072.500.7100655168.510.081639012.090.000152575.790.7932660171.960.061039513.350.000253079.130.8620665175.380.044640014.710.000453582.520.9149670178.770.032040516.150.000654085.950.9540675182.120.023241017.680.001254589.410.9803680185.430.017041519.290.002255092.910.9950685188.700.011942020.990.004055596.441.0000690191.930.008242522.790.0073560100.000.9950695195.120.005743024.670.0116565103.580.9786700198.260.004143526.640.0168570107.180.9520705201.360.002944028.700.0230575110.800.9154710204.410.002144530.850.0298580114.440.8700715207.410.001545033.090.0380585118.080.8163720210.360.001045535.410.0480590121.730.7570725213.270.000746037.810.0600595125.390.6949730216.120.000546540.300.0739600129.040.6310735218.920.000447042.870.0910605132.700.5668740221.670.000247545.520.1126610136.350.5030745224.360.000248048.240.1390615139.990.4412750227.000.000148551.040.1693620143.620.3810755229.590.000149053.910.2080625147.240.3210760232.120.000149556.850.2586: 630150.840.2650765234.590.000050059.860.3230635154.420.2170770237.010.000050562.930.4073640157.980.1750775239.370.000051066.060.5030645161.520.1382780241.680.0000i1附加说明：1本标准由机機工业部提出。：本标准由上海光