塑料收缩率一览表.docxVIP

常用塑胶模具收缩率一览表 编制单位：技质科 编制：唐成保 序 玻璃纤维 密度 收缩率 号 缩写代码 树脂全称 含量 (g/cm) % 1 ABS AcrylonitriteButadiene Styrene / 1.05 0.5% 2 ABS+10%GF AcrylonitriteButadiene Styrene+10% Glass Fiber 10%GF 1.16 0.4% 3 ABS+20%GF AcrylonitriteButadiene Styrene+20% Glass Fiber 20%GF 1.24 0.3% 4 ABS+30%GF AcrylonitriteButadiene Styrene+20% Glass Fiber 30%GF 1.31 0.3% 5 PC Polycarbonate / 1.20 0.6% 6 PC+10%GF Polycarbonate+10% Glass Fiber 10%GF 1.26 0.5% PC+20%GF Polycarbonate+20% Glass Fiber 20%GF 1.27 0.4% PC+30%GF Polycarbonate+30% Glass Fiber 30%GF 1.30 0.3% PC+ABS Polycarbonate+AcrylonitriteButadiene Styrene / 1.15 0.5% AS Acrylonitrite Styrene / 1.07 0.6% PMMA Polymethyl Methacrylate(Acrylic) / 1.18 0.4% POM Polyacetel / 1.42 2% PA66 Polyamide-66 / 1.16 1.3% PA66+10%GF Polyamide-66+10% Glass Fiber 10%GF 1.4 0.6% PA66+20%GF Polyamide-66+20% Glass Fiber 20%GF 1.41 0.5% PA66+30% GF Polyamide-66+30% Glass Fiber 30%GF 1.52 0.45% PA6 Polyamide-6 / 1.15 0.8% PBT Poly(Butylene Terephthalate) / 1.38 1.5% PBT+10% GF Poly(Butylene Terephthalate)+10% Glass Fiber 10%GF 1.60 0.7% PBT+20% GF Poly(Butylene Terephthalate)+20% Glass Fiber 20%GF 1.60 0.6% PBT+30% GF Poly(Butylene Terephthalate)+30% Glass Fiber 30%GF 1.66 0.5% PP Polypropylene / 0.91 1.5% 耐高温PP High Heat Polypropylene / 1.12 1.0% PP 防火 Flame Retarded Polypropylene / 0.95 1.4% 软氯PVC Polyvinyl Chloride Plasticized / 1.35 1.5% 低密 LDPE Low Density Polyethylene / 0.93 2% 高密HDPE High Density Polyethylene / 0.98 3% 弹性体TPE Polyester Thermoplastic Elastomer / 0.92 1.5% PPS Polyphenylene Sulfide / 1.67 0.25% LCP Liquid Crystal Polymer / 1.70 0.02% TPU Thermplastic Polyurethane / 1.24 1.2% 备注:1）收缩率会受加工条件及模具设计的影响而改变； 取向不同，在垂直于流动方向的收缩可能较小（流动方向收缩为横向的 1.6 倍；对于结晶性树脂的倍数更大）； 确定的模具及产品设计，最先制作样模，以得到更准确的收缩值； 尽量参考树脂的产品说明书。