常用塑胶英文单词.docx

常用塑胶英文单词 (2009/11/07 09:14)目录： 常用塑胶英文单词 做塑胶，分享些与之有关的词汇。嵌件insert 嵌件销insert pin 气胀真空成形air assist forming 空气隙air gap 空气顶出air ejection 永久伸长permanent elongation,tension set 永久变形permanent set,permanent deformation 蚀刻,侵蚀etching 应力stress 应力鬆弛stress relaxation 应力龟裂stress cracking 应力集中stress concentration 应力断裂,应力破坏stress rupture 应力.应变曲线stress-strain curve 应力.应变图stress-strain diagram 托板,模板retainer plate 硬度hardness 合模机构mold clamping mechanism 合模力,闭模力locking force,clamping force 开模力mold opening force 悬臂梁cantilever beam 润滑剂lubricant 模具mold,Tools,Tooling 模温度控制器mold temperature controller 模具尺寸mold size 加热管套(料筒)heating cylinder 加热板heating plate 凸轮cam 玻璃纤维glass fiber,fibrous glass 玻璃纤维强化热塑塑胶 fiber glass reinforced thermoplastics,FRTP,glass fiber reinforced thermoplasitcs,GRTP 玻璃纤维强化塑胶glass fiber reinforced plastics,GRP,fiber galss reinforced plastics,FRP. 感光聚合物photopolymer,photo-sensitive polymer 镜面抛光mirror polishing 龟裂cracking 龟裂crack 颗粒料granule 石墨graphite 石墨纤维graphite fiber 间隙, 隙距clearance 模蕊,蕊片,蕊线,蕊孔core 成孔销,模蕊销core pin 成孔销托板core pin plate 公差,容差tolerance 冷料cold slug 冷料井,冷料窝cold slug well 回程销,覆归销surface pin 冷热骤变试验thermal shock test 热应力龟裂thermal stress cracking,TSC 侧向浇口side gate 侧向模蕊(心型)销side draw pin 砂磨sanding 喷砂,打砂sand blast 修饰,涂饰,打光finishing 自断浇口,剪切浇口shear gate 紫外线ultraviolet, UV 紫外线稳定剂UV stabilizer 紫外线吸收剂UV absorber 压花embossing 压花机embossing machine 喷霜,起霜blooming exudation 鯊皮斑shark skin 射出压力injection pressure 射出成形injection molding 射出成形机injection molding machine 射出成形模具injection mold 射出装置injection unit 射出速度injection speed 射出喷嘴,注料嘴injection nozzle 射出容量machine shot capacity 射出率(量)injection rate 煮沸试验boiling test 充填不足,缺料short shot 手动模具hand mold,loose mold 手动油压机hand press 缩窝,凹孔shrinkage pool 衝击试验inpact test 衝击强度impact strength 烧结法,粉铸法sintering 烧结成形法sinter molding 模板mold plate 注射,射料shot 硅橡胶silicone rubber 真空成形vacuum forming 珠光顏料pearlescent pigment 浸渍涂装dip coating 人造皮革artificial leather 废料粉碎机scrap grinder 顶出板,脱模板stripper plate 应力龟裂stress cracking 环境应力龟裂试验environmental stress cracking tes