钢化玻璃检验标准_2.docVIP

Page 1 of 1 RD Dept. 研究部 Global Tempered Glass for Model 6230 Test Report （针对UL标准6230对钢化玻璃做的测试报告） Date of Test: July 10, 2002 测试时间：2002年7月10日 Qty on Test: 125 pcs 测试数量：125PCS Dimension: 4mm x322mm x167mm 玻璃尺寸：4MMX322MMX167MM Product Applicable to: Toaster Oven Model 6230 适用于：烤箱6230 Test Description: 测试描述： Item 序号 Test Description 测试描述 Qty on Test (pcs)测试数量 Conformance 符合 Non-conformance不符合 Conformance Rate符合率 100 Oven Test（加热测试） Put the sample into the oven and heat it to 230℃. Then immediately place it into 20℃ water. No crack allowed. 将样品放入烤箱(炉)中加热至230℃，然后立即放入20℃的水中，不允许有破裂。 125 125 0 100% 101 Impact Test碰撞测试 Drop the steel ball having a weight of 535g from 514mm high onto the glass surface at different points for altogether 3 impacts. No crack and damage allowed. Remark: The impact to the glass edge is not allowed. 将重535克的钢球从离钢化玻璃表面514MM高的地方进行碰撞，要求对不同的点进行三次碰撞，不允许有破裂或损坏。 注：不允许对钢化玻璃边缘进行测试。 125 125 0 100% 102 Density Test 密度测试 Stick the adhesive tape on the surface of the glass. Crack the glass using a tool having a sharp head. The cracked particles sticked on the tape within the area of 50mm x50mm should be not less than 50 ones but not over 300 ones. 将封箱胶粘贴在玻璃的表面，用带尖头的工具打碎玻璃，粘在面积为50X50MM胶带上的玻璃碎片应不少于50个不大于300个。 Remark: The result is that there are 153 particles by average per square. 注：结果是每平方米153个碎片。 125 125 0 100% Dimension Measurement 尺寸测量 Critical 致命 Major 重要缺陷 Minor 轻微缺陷 200 Flatness tolerance at the straight surface +0 –1mm. 直平面承受力为+0 –1mm. 0 0 0 201 Flatness tolerance at the arc surface +0 –2mm. 弧形面承受力为+0 –2mm. 0 0 0 202 Thickness Tolerance +/-0.2mm 厚度承受力为+/-0.2mm 0 0 0 203 No wobble allowed( not exceed 1.5mm) 左右摇摆不超过1.5MM 0 0 2 Appearance Check 外观检测 300 Crack on the edge must not exceed 1mm. 玻璃边缘破裂不超过1MM. 0 0 0 301 No sharp edges and points on the four corners. 四个角上没有锋利的边或点. 0 0 1 302 No dirt and dent on the surface. 表面没有污点 0 0 4 303 Slight scratch (20mm) on the edge must not exceed two ones.玻璃边缘轻微的刮擦（20MM）不能超过2个。 0 0 0 Total 0