毕业论文--真空注型机搅拌机构设计.docVIP

摘 要 本文介绍了型真空注型机搅拌机构设计的一般方法，除进行总体设计外，侧重于运功部件校核和三维仿真的设计。设计中以同类产品（型真空注型机搅拌机构）为基础，通过考察、网上查询、借助参考书的帮助，使设计工作如期完成，能较好的实现规定的各项功能目标。 带传动系统采用的是同步带传动，同步带兼带传动和链传动的优点：传动平稳；传动比准确；几乎不需张紧力，轴压力小；传动效率在98%左右。 三维仿真使用的是UG画图软件，画出三维图后用ADAMS软件进行运动仿真。 文中通过计算、校核确定了同步带轮及部分零件的尺寸及材料，本设计的特色部分是在传动系统的设计同步带传动，使结构紧凑、不需要润滑且保养更加方便。 另外除了两个专题设计部分外，还进行简要的总体设计及主要参数的确定。 由于设计者水平有限，论文一定存在错误和不足之处，请各位老师批评、指正。 关键词：真空注型机，搅拌器，带，三维模拟 Abstract This paper introduces the vacuum injection machines mix the general mechanism design approach, in addition to the overall design, the focus on the pump power components and three-dimensional simulation of the design check. Design to similar products (vacuum injection machines mix body) based on through study, online inquiries, with the help of reference books, so that design work be completed, to better achieve goals set forth in function. Belt drive system uses a belt drive, belt drive and chain drive and with the advantages: stable transmission; drive ratio is accurate; almost without tension, axial pressure is small; transmission efficiency of about 98%. UG-D simulation using drawing software, draw three-dimensional diagram with the ADAMS software emulation. The paper by calculation to determine the timing belt check and some parts wheel size and material, part of the design features of the design in the drive belt drive, so compact, does not require lubrication and maintenance more convenient. Because of designer limited level, the thesis must have some mistakes and weak points. I hope to receive the teachers’ instruction, criticism and helping. Key words: vacuum casting machines, mixers, belt, three-dimensional simulation 目 录 第一章 绪 论 1 1.1引言 1 1.2国内外发展现状 2 1.3课题研究的意义 4 第二章 Ⅱ型真空注型机搅拌机构设计 6 2.1课题研究内容 6 2.2搅拌机构的构成及各部分作用 6 第三章 运动部件设计及校核 8 3.1同步带传动设计与校核 8 3.1.1确定设计功率 8 3.1.2选取同步带型号 8 3.1.3确定带轮节圆直径 9 3.1.4确定中心距a 9 3.1.5初张紧力的校核 10 3.2搅拌器轴的校核 10 第四章 UG三维建模及其装备 12 4.1 UG软件简介 12 4.2 UG设计思路和方法 14 4.3 用UG进行零件设计 14 4.4 UG装配设计 15 第五章ADAMS运动仿真 21 5.1 ADAMS软件介绍 21 5.2 用ADAMS做运功仿真 21 结