采矿工程毕业设计说明书 朱仙庄矿8煤开拓及采区教学设计.docVIP

本科毕业设计说明书 朱仙庄矿8煤开拓及采区教学设计 THE DEVELOPMENT AND INSTRUCTIONAL DESIGN OF ZHUXIANZHUANG COAL MINING 8TH COAL SEAM 学院（部）： 专业班级： 学生姓名： 指导教师： 年 月 日 朱仙庄煤矿8煤开拓及采区教学设计 摘 要 本设计根据对朱仙庄煤矿资料的学习和研究，遵照《煤矿安全规程》和《煤炭工业设计规范》的要求，充分运用所学的知识，以朱仙庄煤矿开采的实际情况为依据，对朱仙庄煤矿的井筒位置、主要设备、井底车场、采煤方法、采煤工艺进行设计。在设计中尽量做到危险最少，效益好，把朱仙庄煤矿建成高产高效的矿井。 朱仙庄煤矿东西北均以10煤露头为界，深部至-800米水平，走向长度为9公里，倾斜宽为1.5-5.8公里，面积为26.3km2，轴部为二迭系煤系底层，四周被奥陶系和石炭系灰岩包围。井田内可采煤层为3，6,7,8,10煤，8 煤为主采煤层，10煤为配采煤层，其余的为局部可采煤层。本设计针对八煤层设计，该层煤煤厚平均9.98m，倾角平均为180，该层煤赋存稳定，为缓倾斜厚煤层。井田工业储量为23338万吨，可采储量为10689万吨。朱仙庄煤矿为煤与瓦斯突出矿井，瓦斯赋存表现为北低南高的特点。矿井北翼受瓦斯的影响小，南翼受瓦斯的影响大。8煤层属于很容易自燃发火的煤层。煤层自燃期一般是3～6个月。 朱仙庄煤矿设计生产能力为150万吨。采用立井多水平上（下）山开拓，第一水平标高为-435米，第二水平标高为-700米。采煤方法为单一走向长壁采煤法，采煤工艺主要为综合机械化放顶煤回采工艺。轨道大巷采用蓄电池电机车牵引1.5吨固定式矿车运输。主井采用多绳摩擦式提升，副井采用罐笼提升。矿井通风方式为中央边界式。 关键词：朱仙庄矿，开拓，巷道布置，通风 THE GRADUATION DESIGN OF ZHUXIANZHUANG COAL MINE ABSTRACT In this paper, based on information Zhuxianzhuang Coal learning and research, in accordance with the Coal Mine Safety Regulations and design specifications of the coal industry, to make full use of knowledge to Zhuxianzhuang the actual situation of coal mining, based on the Zhuxianzhuang coal mine under the group to borehole location, major equipment, shaft bottom, mining methods, mining process has detailed instructions of the design. In the design of the risk at least as far as possible, effective, and the Zhuxianzhuang into highly efficient and high-yielding coal mines. What ZhuXianZhuang coal in north of 10 coal outcrops, deep - 800 meters in length, to tilt width for 9 km, 1.5-5.8 kilometers, the area for 26.3 km2, axis for coal layer of superposition, surrounded by ordovician and carboniferous limestone surrounded. Within the field of coal, coal 3,6,7,8,10 for coal, coal and coal is mainly with 10 coal, the rest for local coal. In this design, the design of eight seam thickness of coal layer are 8.40 meters, Angle, the average for 180 coal layer for slope stability, th