建筑结构设计计算守则_大全_Load Combination(LBeam).xls

Combination Force(L2) Combination Force(L1) Adjustments FACTOR ETABS Force Combination (L2) Combination Element Name Overall Load_Combination_L1.Load_Combination_L1 Load_Combination_L2.Load_Combination_L2 Load_Combination_Wind.Load_Combination_Wind Story Load Loc P V2 V3 T M2 M3 Element No. id 构件 类型 调整项 参照规范 条文 规范 调整系数 本工程设计采用调整系数 剪力墙 弯矩 高规4.9.2条4(1)款，特一级 底部加强部位：1.1 一般部位：1.3 剪力 底部加强部位：1.9 一般部位：1.2 轴力 － 外框柱 高规6.2.1条，6.2.4条， 8.1.4条， 4.9.2条1款，特一级 框架柱： 1.4x1.2＝1.68 角柱： 1.4x1.2x1.1＝1.85 1.4x1.2x1.4x1.2x1.1＝3.10 当Vf 0.2V0 ，先乘以调整系數: Min(0.2V0 /Vf ,1.5) 巨型斜撑 JGJ99-98第6.4.5条 单斜杆支撑： 连梁 高规7.2.22， 一级 框架梁 高规6.2.5， 4.9.2条2款，特一级 1.3x1.2=1.56 材料 结构构件 受力状态 γRE 钢 柱、梁 支撑 节点板件，连接螺栓 连接焊缝 梁 受弯 轴压比小于0.15的柱 偏压 轴压比不小于0.15的柱 抗震墙 各类构件 受剪、偏拉 型钢混凝土 柱 压 各类构件及节点 受剪 焊缝及高强螺栓 底部加强部位 一般部位 - 框架柱 1.4x1.2x1.4x1.2=2.82 单斜杆支撑： Job No. Sheet No. Rev. Ove Arup Partners Calculation Sheet Member / Location Job Title: Drg. Ref. Made by qiang.l Date MS ACCESS DATABASE PATH: File location Model name CHECKING CONTROL INFORMATION: NOTE: Story ETABS Force AnalysisSect Element No AnalysisSect No Load Combination for Beam 混凝土 SDL 1. The treated Combination Force database will be saved in the same Model database file. The tables names are like following: 2. Wind include from Combination 1 to 74;Wind + Level include from Combination 75 to 386. Combination Force of LBeam Wind,Combination Force of LBeam L1,Combination Force of LBeam L2 Combinations factor Member Force after Combination(Loc 1) Member Force after Combination(Loc2) Member Force after Combination(Loc3) Adjustments Factor Member Force(loc1) after Adjustment Member Force(loc2) after Adjustment Member Force(loc3) after Adjustment Combination SDL id Element No. Story No. to Axial Force to Shear Force to Moment γ0 γRE DL LL GBSXY GBSYX SW GBSL1XY GBSL1XY GBSL1YX GBSL1YX WT100D2 WT100D2 WT100D4 WT100D5 WT100D7 Shear-gravity ratio adjustment: Time-history adjustment: L81upper:1.7 各种组合的组合值系数 Combination DL LL WT100D1 WT100D3 WT100D6 T8P T8N GBSXT GBSYT G