ANSYS-DYNA教程.pptVIP

下载本文档

10
0
约2.27千字
约 4页
2017-08-25 发布于河南
举报
版权申诉

ANSYS-DYNA教程.ppt

1、本文档共4页，可阅读全部内容。
2、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。
3、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
4、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。
5、该文档为VIP文档，如果想要下载，成为VIP会员后，下载免费。
6、成为VIP后，下载本文档将扣除1次下载权益。下载后，不支持退款、换文档。如有疑问请联系我们。
7、成为VIP后，您将拥有八大权益，权益包括：VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
8、VIP文档为合作方或网友上传，每下载1次，网站将根据用户上传文档的质量评分、类型等，对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档

EXPLICIT DYNAMICS with ANSYS/LS-DYNA Training Manual Training ManualExplicit Dynamics with ANSYS/LS-DYNA Inventory Number: 001458 First Edition ANSYS Release: 5.7 Published Date: March 15, 2001 Registered Trademarks: ANSYS? is a registered trademark of SAS IP Inc. All other product names mentioned in this manual are trademarks or registered trademarks of their respective manufacturers. Disclaimer Notice: This document has been reviewed and approved in accordance with the ANSYS, Inc. Documentation Review and Approval Procedures. “This ANSYS Inc. software product (the Program) and program documentation (Documentation) are furnished by ANSYS, Inc. under an ANSYS Software License Agreement that contains provisions concerning non-disclosure, copying, length and nature of use, warranties, disclaimers and remedies, and other provisions. The Program and Documentation may be used or copied only in accordance with the terms of that License Agreement.” Copyright ? 2001 SAS IP, Inc. Proprietary data. Unauthorized use, distribution, or duplication is prohibited. All Rights Reserved. Table of Contents Lecture Notes: Chapter 1 Introduction Chapter 2 Elements Chapter 3 Part Definitions Chapter 4 Material Definitions Chapter 5 BCs, Loading, and Rigid Bodies Chapter 6 Contact Surfaces Chapter 7 Solution and Simulation Controls Chapter 8 Postprocessing Chapter 9 Restarting Chapter 10 Explicit-to-Implicit Sequential Solution Chapter 11 Implicit-to-Explicit Sequential Solution Chapter 12 ANSYS/LS-DYNA Drop Test Module Chapter 13 Summary Exercises Inputs: E1 Introduction to Exercises E2 Simulating a Deep Drawing Process E3 Utilizing Parts in a Contact Analysis E4 Define a Material Model with Plasticity and Failure E5 Conducting a Spotweld Failure Analysis E6 Applying an Initial Velocity Load in a Contact Analysis E7 Buckling and Folding of a Beam E8 Bending of a Pipe by a Punch E9 Performing a Small Restart E10 Springback Analysis