盒体冲压件模具设计论文.docVIP

摘 要 本论文主要是对落料拉伸复合模而做的设计。这套复合模不但节约了原材料，为工厂带来了利益和效率，更主要的是它把这几个原本不容易合在一起的制造工艺通过特殊装置实现了。很大程度的提高了工作效率，并把原来一套以上才能完成的工艺用这套复合模完成了。 此论文主要阐述了我国模具现状和发展趋势、对零件的工艺分析、模具结构的设计、模具装配与部装图的设计。 其中工艺分析对零件的特性和材料性能做了简单的介绍，工艺计算主要是为设计选件打基础，通过大量的计算来确定一些标准件选择的尺寸和压力机的确定等。经过第二章计算和分析后进行模具结构的选择，其中包括标准件的选择和非标准的设计等。要做到标准件的选择正确以及非标准件的设计合理。最后用CAD绘制出模具的装配图和部装图，阐明装配时需要注意的事项。 关键词 冲压工艺；模具设计；CAD Abstract This paper is blanking punching and bending modulus composites do the design. The composite model not only saves raw materials for factories and the interests of efficiency, more importantly, it is not easy these few original combination of the manufacturing process through special devices has been achieved. A large degree of increase work efficiency, and above the original set to complete the process by the completion of this compound die. This thesis expounded Chinas current situation and development trend die, the part of the process, the structure of mold design, mold assembly of the equipment and the design plans. Part of the craft of the characteristics and properties of materials with a brief introduction, process calculation is the foundation for the design options through a lot of calculation to determine the criteria of choice of the size and the setting of press. After the second chapter calculation and analysis of the mold structure options, including the choice of standard and non-standard design. To achieve the correct choice of standard and non-standard pieces of rational design. Finally, a CAD drawing mold assembly of the equipment and plans to clarify when assembling need attention. Keywords： stamping process; die design; CAD 不要删除行尾的分节符，此行不会被打印目录 摘要 I Abstract II 第1章 绪论 1 1.1国内模具的现状和发展趋势 1 1.1.1 国内模具的现状 1 1.1.2 国内模具的发展趋势 3 1.2 国外模具的现状和发展趋势 5 1.3 课题研究的目的及论文主要内容 6 第2章 工艺分析 7 2.1 零件的特性 7 2.1.1 零件的工艺性 7 2.1.2 零件的形状 7 2.1.3 材料性能 8 2.2 工艺计算 9 2.2.1 毛坯直径的确定 9 2.2.2 零件锥形拉伸次数的确定 10 2.2.3 缷料力、顶件力和推件力的计算 12 2.2.4压力机的选择 13 2.3 本章小结 14 第3章 冲压模具零部件的选择与设计 15 3.1 冲裁间隙以及凸、凹模的刃口尺寸计算 15 3.1.1 冲裁模凸、凹模刃口尺