KXT-W型可曲挠橡胶接头.doc

KXT-W型可曲挠橡胶接头 Model KXT-W Floating Flange Rubber Expansion Joints Page28 材料表 Table of Materilals 序号Serial No 部位Prtion 材料Material 1 主体Main body 极性橡胶Polarized rubber 2 内衬Lining 尼龙帘布Nylon cord fabric 3 骨架Frame 硬钢丝Hard steel wire 4 法兰Flange 软钢Mild steerl 技术条件 Technical Consition 公称通径 DN mm(寸)Nominal core diameter 32-300(11/4-12) 350-500(14-20) 工作压力 MPa(kg.f/cm2)Working pressure 1.5(15) 0.8(8) 爆破压力 MPa(kg.f/cm2)Bursting pressure 4.5(45) 2.4(24) 真空度 Vacuity Kpa(mm Hg) 86.7(650) 适用温度 Applicable temp. -20℃-80℃(普通型) 　+80℃-135℃(特殊配方) 适用介质 Applicable media 空气、压缩空气、水、海水、热水、弱酸 Air.Compressed air.Water.Sea Water.Hot Water.Weak acid.Etc 接头两端可任意偏转,便于自由调节轴向或横向位移.Both ends of the joint can be arbitray deflected for free adjustment of axial or lateral displacement. 注：普通型产品中能在80℃以下，如需135℃以下需指明，更换橡胶配方。压力较高及冲击力较大时宜采用限位拉杆装置。 Note:ordinary type products can only be used under 80℃. if temperature is higher than 130℃, please show clearly, ingredient of the rubber will be changed. Restricting pull rod is necessary, when pressure is high and impulse is great. 公称通径、长度、位移数值与法兰主要数据表 Table of Main Parameters of Nominal Core Diameter，Length，Displacement Value and Flange 公称能径Nominal core diameter 长度Length l(mm) 螺栓数No.of bolt n 螺栓孔直径Diameter of bolt hole do(mm) 螺栓孔中心圆直径Diameter of bolt hole center circlen D1 (mm) 轴向位移Axial displacenment(mm) 横向位移Lateral displace-ment(mm) 偏转角度Angle of deflection (α1+α2) (mm) (寸 in) 伸长Strech 压缩Compression 32 (11/4) 150 130 4 15 89 12 20 14 150 40 (11/2) 150 130 4 15 98.5 12 20 14 150 50 (2) 150 130 4 19 121 12 20 14 150 65 (21/2) 150 130 4 19 139.5 12 20 14 150 80 (3) 150 130 4 19 153 12 20 14 150 100 (4) 150 130 8 19 190 12 20 14 150 125 (5) 150 130 8 22.5 216 12 20 14 150 150 (6) 150 130 8 22.5 242 12 20 14 150 200 (8) 150 130 8 22.5 298 12 20 14 150 250 (10) 150 130 12 22.5 362 16 25 22 150 300 (12) 150 130 12 22.5 432 16 25 22 150 350 (14) 200 12 28.5 476 16 25 22 150 400 (16) 200 16