UGCAM中英对照.docVIP

UG术语中英对照表CAM部分A? Aaxis??????? A轴? ACL???????? ASCII刀位文件? ACL/BCL Generation??? ACL/BCL 生成器? Action Mode???? 激活模式? Activation Range? 自动进刀范围? Add Arcs??? 增加圆弧? Add Ranges?? 增加切削范围? Add To List??? 增加到列表? ADDED STOCK?? 增加的余量? Adding a post command??? 增加一个后置命令? Additional Passes? 附加轨迹? Adjust Active???? 刀补激活? Adjust Region??? 刀补范围? Adjust Register? 刀补寄存器? After each Engage? 每次进刀之后? After Each Pass??? 每条刀轨之后? After each Retract? 每次退刀之后? After Each Subop?? 每次子操作之后? After Last Motion?? 最终运动之后? All but Faces?? 除了面的所有类型? All but Steep?? 除了陡壁的所有类型? All Loops????? 所有的环? All Passes??? 所有刀轨? Allow Oversize Tool? 允许偏大刀具? Analysis Tools?? （刀轨）分析工具? Analyze Cut Shapes?? 分析切削外形? Analyze Tool Path?? 分析刀轨? ANGLE 1,ANGLE 2,DISTANCE???? 角1,角2,距离? Angle Tolerance??? 角度公差? ANGLE,ANGLE,PLANE???? 角度,角度,平面? Angle/DS???? 角度/驱动面? Angle/PS???? 角度/零件面? Animate???? 动态模拟? Animate Tool Path?? 动态模拟刀轨? Animation Speed??? 动态模拟速度? Append? 附加? Appended Text Active?? 附加的文本激活? Appending Objects??? 附加对象? Approach? 趋近速度? Approach Marker 趋近运动标记? Aquamarine??? 蓝绿色? Arc Center Probe? 圆心自动定位? Arc Output Type??? 圆弧输出类型? Arc:Normal Tool axis 圆弧:垂直刀具轴? Arc:Parallel to Cut??? 圆弧:平行切削方向? Arc:Parallel Tool axis?? 圆弧:平行刀具轴? Area Centroid?????? 面积质心? Area Milling Drive??? 区域铣削驱动? Area Milling 区域铣削? As Final??? 与最终相同? As Initial???? 与最初相同? At Angle to DS? 与驱动面成角度? At Angle to PS? 与零件面成角度? Automatic? 自动的? Auxfun? 辅助功能? Auxfun Value?? 辅助功能值? Available Functions? 有效功能? Avoid? 避让? AVOID CLEARANCE??? 避让安全平面? Avoidance Geometry? 避让几何体? Away From Line 远离线? Away From Point? 远离点? Axis??? 轴? Axis Off?? 轴关闭? Axis On?? 轴开启? B? Backburn??? 反切口? Bad Chains? 无效的链接? Bad Segments? 无效的段? Bandwidth? 带宽? Barrel Cutter? 鼓形刀? Baxis?? B轴? BCL???? 二进制文件? Before 1st Motion??? 第一次运动之前? Before each Engage??? 每次进刀之前 Before each Retract??? 每次退刀之前? Blank Boundary? 毛坯边界? Blank Distance 毛坯距离? Blank Geometry 毛坯几何体? Blank Shape??? 毛坯外形? Blank Stock 毛坯余量? Blank 毛坯? Blind Hole? 盲孔? Blue???? 蓝色? Boring Radius?? 切削刃到车刀轴距离? Bottom Regions? 底部区域? Bottom Surf