流控大师安装教程.docVIP

1.U盘启动进入系统. 开始找硬件到login:按以下命令操作 Login:root (控制台帐号root,必须为小写) Passwd:root(控制台默认密码为root,必须为小写) 进入后如下 Panabit8#dmesg (列表硬件信息命令)大概如下 ad0: 1920MB PQI IDE DiskOnModule ra6h.a01 at ata0-master UDMA33 (这里代表硬盘) 我们要找的就是如ad0或者是da0的..必须要清楚.别搞错了.安装的时候要指定PA安装到那个硬盘下.我这里需要把PA安装到我的2GPQI电子盘下就是;ad0 da0 at umass-sim0 bus 0 target 0 lun 0 da0: Kingston DataTraveler II+ 1.13 Removable Direct Access SCSI-0 device da0: 40.000MB/s transfers da0: 245MB (502784 512 byte sectors: 64H 32S/T 245C) GEOM: da0: partition 1 does not start on a track boundary. GEOM: da0: partition 1 does not end on a track boundary. Ifconfig命令:此为列表你的网卡,必须看仔细.最好先把网线接到你管理卡上 Panabit8# ifconfig 信息如下: alc0: flags=8843UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST metric 0 mtu 1500 options=3198VLAN_MTU,VLAN_HWTAGGING,VLAN_HWCSUM,TSO4,WOL_MCAST,WOL_MAGIC ether 6c:f0:49:83:03:1a inet netmask 0xfffffc00 broadcast 55 media: Ethernet autoselect (100baseTX full-duplex) status: active em0: flags=8802BROADCAST,SIMPLEX,MULTICAST metric 0 mtu 1500 options=9bRXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,VLAN_HWCSUM ether 00:1b:21:5d:26:9b media: Ethernet autoselect status: no carrier em1: flags=8802BROADCAST,SIMPLEX,MULTICAST metric 0 mtu 1500 options=9bRXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,VLAN_HWCSUM ether 00:1b:21:5d:22:c9 media: Ethernet autoselect status: no carrier 上面看active代表已经连接. 网卡名为alc0,我就是要把这快网卡作为WEB管理用, no carrier为未连接. 安装命令: Panabit8# ./setup(看仔细.前面有一个点的) 回车 Please confirm whether or not to continue the installation! Do you want to continue(y/n[n])?y (是否要继续安装.当然选Y继续)回车 Following disks are detected: da0 ad0 Please select one [da0]:ad0 (选择你要把PA安装到的硬盘下面.默认da0,我这里选择ad0要把他安装在我的电子硬盘上)回车 We begin to format the disk ad0 and begin to install FreeBSD 8.0! Do you want to continue(y/n[y])?y(按Y确认)回车.下面就是格式化磁盘.安装,等到如下信息 ****** Congratulations ******! You have successfully installed Panabit on your system! Following interfaces are installed in y