HDPE PIPE EXTRUSION.ppt

A2-11-2-e 聚乙烯管材挤出 HDPE Pipe Extrusion 巴顿菲尔震雄塑料设备有限公司Battenfeld Chen Extrusion Systems 聚乙烯管材挤出 HDPE Pipe Extrusion 内容 Contents HDPE 管材概述 General on HDPE Pipe 聚乙烯管材挤出 HDPE Pipe Extrusion HDPE 管材概述 General on HDPE Pipe 聚乙烯管材挤出 HDPE Pipe Extrusion 耐腐蚀性。不生锈，不腐烂，不受侵蚀。 不泄漏。热熔接头形成一个同质的单一系统。熔合接头甚至比管道本身具有更高强度。 保持最佳流量。不结垢和滋生生物。 能够承受外部重载。 Corrosion resistant. Does not rust, rot, or corrode. Leak tight. Heat-fused joints create a homogenous, monolithic system. The fusion joint is as strong or stronger than the pipe. Maintains optimum flow rates. Has a high resistance to scale or biological build-up. Strength to withstand external loads 聚乙烯管材挤出 HDPE Pipe Extrusion 高抗疲劳强度。实质上消除了由于严寒引起的管材破坏。 管材的柔韧性减少了接头数量。盘管直径是管材外径的20到25倍。 重量轻和增加的长度节省人力和设备。 High strain allowance. Virtually eliminates breakage due to freezing pipes. Fewer fittings due to pipe flexibility. Allowable bending radius of 20 to 25 times outside diameter of pipe. Light weight and longer lengths allow for significant savings in labor and equipment. 聚乙烯管材挤出 HDPE Pipe Extrusion 天然气和石油管路 水管（饮用水，废水，排水，灌溉等等） 光纤电缆套管 Natural gas and oil lines Water lines (potable water, wastewater, drainage, irrigation, etc.) Electrical optical conduit 聚乙烯管材挤出 HDPE Pipe Extrusion 管道衬装（化学，煤气和下水管） 垃圾掩埋回收；矿业；酸性/腐蚀性物质管路；泥浆输送… Relining (chemical, gas sewer lines) Landfill reclamation; mining; acid lines; caustic lines; mud line… 聚乙烯管材挤出 HDPE Pipe Extrusion HDPE 管材挤出生产线 HDPE Pipe Extrusion Lines 聚乙烯管材挤出 HDPE Pipe Extrusion Single Screw Extruder 单螺杆挤出机 聚乙烯管材挤出 HDPE Pipe Extrusion 聚乙烯管材挤出 HDPE Pipe Extrusion High specific throughput Low melt temperature Excellent melt homogeneity Wide application range 挤出量高 熔体温度低 优异的熔体均匀度 应用范围广 聚乙烯管材挤出 HDPE Pipe Extrusion 聚乙烯管材挤出 HDPE Pipe Extrusion All our single screw extruders are equipped with bimetallic barrel. Besides, screw fights are hard-surfaced with STELLITE. Benefit Good abrasion resistance Outstanding corrosion resistance 现在，巴顿菲尔所有单螺杆挤出机都采用双金属机筒，螺杆螺棱部分用钨铬钴合金做表面硬化处理 优点： 良好的耐磨损性 出色的耐腐蚀性 聚乙烯管材挤