- 1、本文档共3页,可阅读全部内容。
- 2、原创力文档(book118)网站文档一经付费(服务费),不意味着购买了该文档的版权,仅供个人/单位学习、研究之用,不得用于商业用途,未经授权,严禁复制、发行、汇编、翻译或者网络传播等,侵权必究。
- 3、本站所有内容均由合作方或网友上传,本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺!文档内容仅供研究参考,付费前请自行鉴别。如您付费,意味着您自己接受本站规则且自行承担风险,本站不退款、不进行额外附加服务;查看《如何避免下载的几个坑》。如果您已付费下载过本站文档,您可以点击 这里二次下载。
- 4、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等,请点击“版权申诉”(推荐),也可以打举报电话:400-050-0827(电话支持时间:9:00-18:30)。
查看更多
Using QNAP NAS VLAN with Virtualization Deployment
About VLAN
VLAN or Virtual Local Area Network can be used to create different network segments for different devices to communicate with each other as if they were in a private network regardless of their physical location. The devices joined to a VLAN can only be accessed by other devices of the same VLAN ID.
QNAP NAS can be integrated in a VLAN by the VLAN feature. By adding the NAS to the VLAN, only the devices using the same VLAN are able to access the NAS. This increases data security of the NAS.
This how-to shows you how to set up a VLAN in a VMware vSphere environment and join the NAS to a VLAN to allow private access to the NAS.
Follow the steps below to integrate the NAS to your virtualization environment by VLAN.
1. Configure VLAN on a switch
To allow VLAN packets to be transmitted through the switch or router, you may need to configure the port settings. In this example, we use Cisco 2960G switch and we need to configure the network port to support 802.1Q standard. First, login Cisco switch with an administrator account. Enter the following command where XX is the specific network port number for VLAN communication.
# enable# configure terminal# interface gigabitEthernet 0/XX# switchport mode trunk
Please refer to the user manual of your switch for VLAN configuration.
2. Enable VLAN on QNAP NAS
Note:?The VLAN feature is supported by Intel-based QNAP NAS only.
Login the NAS as an administrator. Go to ‘System Administration ‘Network‘TCP/IP’. Choose the network interface to add a VLAN ID, click ‘Edit’.
If your NAS supports two LAN ports, we recommend you to enable VLAN on only one network interface first. If a wrong VLAN is chosen and you could not connect to the NAS via VLAN, you can connect to the NAS via the second network interface.
In case you change the VLAN on all the interfaces and lose connection, you can press the reset button on the NAS for 3 seconds to restore the default network configuration
您可能关注的文档
- 《(好)PCB基材及工艺设计、工艺标准》.ppt
- 《(很好的嵌入式linux启动过程分析》.doc
- 《+MPa车用轻质高压储氢容器自增强理论建模》.pdf
- 《-MTI缩略语》.doc
- 《0.周建武《MBA联考奇迹300分》第四版--逻辑》.doc
- 《00-12年MBA管理专硕逻辑真题》.doc
- 《00001---硫化钼---硒化钼--垂直阵列----2016---nano letter》.pdf
- 《0001 MS培训教程》.pdf
- 《001 MS建模问题集锦-小木虫》.pdf
- 《002电话礼仪-新动力培训》.ppt
- 《JJF 2132-2024荧光紫外灯人工气候老化试验装置校准规范:辐射照度参数》.pdf
- JJF 2120-2024轮速传感器校准规范.pdf
- 计量规程规范 JJF 2120-2024轮速传感器校准规范.pdf
- 《JJF 2129-2024钙钛矿太阳电池校准规范:光电性能参数》.pdf
- JJF 2129-2024钙钛矿太阳电池校准规范:光电性能参数.pdf
- 《JJF 2120-2024轮速传感器校准规范》.pdf
- JJF 2117-2024沥青混合料理论最大相对密度仪校准规范.pdf
- JJF 2116-2024特定蛋白分析仪校准规范.pdf
- 《JJF 2116-2024特定蛋白分析仪校准规范》.pdf
- 计量规程规范 JJF 2117-2024沥青混合料理论最大相对密度仪校准规范.pdf
文档评论(0)