单片机实验模型及结果（打印版）.docVIP

提醒：用A5纸打印 AT89C51单片机PWM汇编程序 ADC EQU 35H CLOCK BIT P2.4 ST BIT P2.5 EOC BIT P2.6 OE BIT P2.7 PWM BIT P3.7 ORG 00H SJMP START ORG 0BH LJMP INT_T0 START: MOV TMOD,#02H MOV TH0,#20 MOV TL0,#00H MOV IE,#82H SETB TR0 WAIT: CLR ST SETB ST CLR ST JNB EOC,$ SETB OE MOV ADC,P1 CLR OE SETB PWM MOV A,ADC LCALL DELAY CLR PWM MOV A,#255 SUBB A,ADC LCALL DELAY SJMP WAIT INT_T0: CPL CLOCK RETI DELAY: MOV R6,#1 D1: DJNZ R6,D1 DJNZ ACC,D1 RET END AT89C51控制直流电动机汇编程序 ADC EQU 35H CLOCK BIT P2.4 ST BIT P2.5 EOC BIT P2.6 OE BIT P2.7 PWM BIT P3.7 ORG 00H SJMP START ORG 0BH LJMP INT_T0 START: MOV TMOD,#02H MOV TH0,#20 MOV TL0,#00H MOV IE,#82H SETB TR0 WAIT: CLR ST SETB ST CLR ST JNB EOC,$ SETB OE MOV ADC,P1 CLR OE SETB PWM MOV A,ADC LCALL DELAY CLR PWM MOV A,#255 SUBB A,ADC LCALL DELAY SJMP WAIT INT_T0: CPL CLOCK RETI DELAY: MOV R6,#1 D1: DJNZ R6,D1 DJNZ ACC,D1 RET END AT89C51控制步进电动机汇编程序 ORG 00H START: MOV DPTR,#TAB1 MOV R0,#03 MOV R4,#0 MOV P1,#3 WAIT: MOV P1,R0 ;初始角度,0度 MOV P0,#0FFH JNB P0.0,POS ;判断键盘状态 JNB P0.1,NEG SJMP WAIT JUST: JB P0.1,NEG ;首次按键处理 POS: MOV A,R4 ;正转9度 MOVC A,@A+DPTR MOV P1,A ACALL DELAY INC R4 AJMP KEY NEG: MOV R4,#6 ;反转9度 MOV A,R4 MOVC A,@A+DPTR MOV P1,A ACALL DELAY AJMP KEY KEY: MOV P0,#03H ;读键盘情况 MOV A,P1 JB P0.0,FZ1 CJNE R4,#8,LOOPZ ;是结束标志 MOV R4,#0 LOOPZ: MOV A,R4 MOVC A,@A+DPTR MOV P1,A ;输出控制脉冲 ACALL DELAY ;程序延时 INC R4 ;地址加1 AJMP KEY FZ1: JB P0.1,KEY CJNE R4,#255,LOOPF;是结束标志 MOV R4,#7 LOOPF: DEC R4 MOV A,R4 MOVC A,@A+DPTR MOV P1,A ;输出控制脉冲 ACALL DELAY ;程序延时 AJMP KEY DELAY: MOV R6,#5 DD1: MOV R5,#080H DD2: MOV R7,#0 DD3: DJNZ R7,DD3 DJNZ R5,DD2 DJNZ R6,DD1 RET TAB1: DB 02H,06H,04H,0CH DB 08H,09H,01H,03H;正转模型资料 EN