- 1、本文档共15页,可阅读全部内容。
- 2、原创力文档(book118)网站文档一经付费(服务费),不意味着购买了该文档的版权,仅供个人/单位学习、研究之用,不得用于商业用途,未经授权,严禁复制、发行、汇编、翻译或者网络传播等,侵权必究。
- 3、本站所有内容均由合作方或网友上传,本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺!文档内容仅供研究参考,付费前请自行鉴别。如您付费,意味着您自己接受本站规则且自行承担风险,本站不退款、不进行额外附加服务;查看《如何避免下载的几个坑》。如果您已付费下载过本站文档,您可以点击 这里二次下载。
- 4、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等,请点击“版权申诉”(推荐),也可以打举报电话:400-050-0827(电话支持时间:9:00-18:30)。
查看更多
《rfic_hfss螺旋电感设计》.doc
Report
Create a project
FileNew
Right click project name rename: Inductor
Project Insert HFSS Design
HFSS Solution Type Driven Terminal OK
Create 3-D model
Modeler units um OK
Create Substrate
Draw box input the following parameters
Attribute name: sub Material edit Add material input the following parameters
OK OK OK
Create Oxide
Draw box input the following parameters
Attribute name: oxide Material edit Add material input the following parameters
OK OK OK
Create passivation
Draw box input the following parameters
Attribute name: pass Material edit Add material input the following parameters
OK OK OK
Create air
Draw box input the following parameters
Attribute name: air Material vacuum
Select air HFSS Boundaries Assign Radiation
Create ground
Draw rectangle input the following parameters
Attribute name: gnd OK
Select gnd HFSS Boundaries Assign PerfectE name PerfE gnd
Create spiral
Select Add Material name: rfic_met Relative Permittivity :2.8e7 OK OK
Offset Origin 0, 0, 304.8
Create spiral path Draw line following steps of the PDF ……
Modeler Grid Plane XZ
Draw rectangle input the following parameters
Attribute name spiral OK
Select Polyline1, spiral Draw sweep Along pass
Modeler Grid Plane XY
Create underpass
Draw box input the following parameters
Attribute name: underpass OK
Create via
Draw box input the following parameters
Attribute name: via1 OK
Draw box input the following parameters
Attribute name: via2 OK
The spiral is shown below
Create feed
Draw box input the following parameters
Attribute name: feed OK
CtrlA HFSS Mesh Operations Assign Inside Selection Length based set as below OK
Select material: pec
Create ground ring
Draw box input the following parameters
Attribute name: ring
Draw box input the following parameters
Attribute name: inner
Select ring and inner Modeler Boolean Subtract set as below OK
Create extension
Draw box input the following para
您可能关注的文档
- 《Prepare a resume – 如何制作英文简历》.ppt
- 《proe电缆模块操作实例》.doc
- 《protel 电路板设计思考题》.doc
- 《Protel99SE印制电路板设计教程--第2章绘制电路原理图》.ppt
- 《Protel99SE印制电路板设计教程--第3章__原理图元件库编辑》.ppt
- 《Protel99SE电路设计实例教程1(共13章)》.ppt
- 《Protel_DXP电路设计入门(一)》.ppt
- 《Protel_DXP电路设计入门(二)》.ppt
- 《protel实用教程》.ppt
- 《Protel电路板仿真设计课程设计》.doc
- (4篇)XX区抓党建促基层治理培训心得体会汇编12.docx
- 汇编1154期-在培训班上的讲话汇编(3篇).doc
- 汇编1173期-专题党课讲稿汇编(3篇)112.doc
- 汇编1076期-主题党课讲稿汇编(3篇).doc
- 汇编1177期-学习心得体会汇编(3篇)112.doc
- (6篇)党和国家机构改革心得体会汇编.docx
- 汇编1166期-坚定理想信念、全面从严治党、担当作为专题党课讲稿汇编(3篇)112.doc
- 汇编1174期-专题党课讲稿汇编(3篇)112.doc
- 教育13期-主题教育学习心得体会、研讨发言材料参考汇编(3篇).doc
- 汇编1458期-心得体会研讨发言提纲参考汇编(3篇)123.doc
文档评论(0)