某经济开发区污水处理厂设计培训课程.doc

南通某经济开发区污水处理厂设计 摘要：本设计主要是市污水处理厂的设计，该污水厂最终采用现行的SBR变形形式CASS工艺。是周期循环活性污泥法的简称，又称为循环活性污泥工艺是在SBR的基础上发展起来的，即在SBR池内进水端增加了一个生物选择器，实现了连续进水(沉淀期、排水期仍连续进水)，间歇排水。该污水厂设计的关键词：污水处理厂；CASS Abstract: This design is the design of wastewater treatment plant of a economic development zone of Nantong City, the sewage treatment plant is located in the economic development zone, based on the analysis of the raw water quality, sewage and reference data processing large, comprehensive consideration of technical, economic and other factors, the current SBR deformation form of CASS process. CASS is a cyclic activated sludge method abbreviation, also known as cyclic activated sludge technology, is in the SBR developed on the basis of SBR, namely in the pool water inlet end adds a biological selector, realizes continuous water (precipitation, drainage period is still continuous, intermittent drainage.). The design of wastewater treatment plant process water, coarse grid, pumping station, fine grid, advection sedimentation tank, CASS tank → Pukuai filter, disinfection pool, water. Treatment process of sludge is CASS, sludge pumping station, sludge storage tank, concentrated pool. The effluent can meet the design requirements. Key words: Sewage treatment plant; CASS; sludge disposal 目 录 摘要 I Abstract II 1 绪论 1 1．1 课题研究意义 1 2污水厂概况 1 2.1地理位置及气候 1 2.2设计规模及进出水水质 2 2.3 处理程度的计算 2 3 城市污水处理设计 2 3.1污水处理工艺流程选择 2 3.2 工艺比较 3 3.2.1氧化沟方案 3 3.2.2 CASS工艺方案 4 3.3方案的确定 6 3.4工艺流程图 6 4 污水处理构筑物的设计说明 7 4.1 粗格栅的设计 7 4.1.1 格栅尺寸 7 4.1.2 通过格栅的水头损失 h1 8 4.1.3 栅后槽总高度 H 8 4.1.4 栅槽总长度 L 8 4.1.5 每日栅渣量 W 9 4.1.6 格栅的选择 9 4.2提升泵房 10 4.3细格栅 10 4.3.1细格栅的隔栅尺寸 10 4.3.2通过格栅的水头损失 h1 11 4.3.3 栅后槽总高度 H 11 4.3.4 栅槽总长度 L 11 4.3.5 每日栅渣量 W 12 4.4 平流式沉砂池 12 4.4.1 功能： 12 4.4.2 设计计算 13 4.4.3主要工程内容 14 4.5 CASS生化池 15 4.5.1 CASS的功能 15 4.5.2 设计计算 15 4.6 滤池设计计算 20 4.7接触消毒池与加氯间 21 4.7.1 设计说明： 21 4.7.2 设计计算 21 5. 污泥的处理与处置 23 5.1贮泥池计算 23 5.2 污泥提升泵房 23 5.3 浓缩池设计计算 23 5.4 污泥脱水计算 25 5.4.1 浓缩后污泥量 25 5.4.2 脱水工艺及脱水设备的选择 25 6 污水厂总