数控技术课件..ppt

三、 教学方法 2）用工程化的观点，结合案例进行教学。 （2）如何编程？ 1）编程核心是工艺，而工艺与具体加工环境等密切相关 机床、产量等，从可行性、经济性等方面考虑。 三、 教学方法 （3）如何简化编程？ 案例分析、视频演示、实际演练、机床实践 谢 谢！ 工步2：钻Φ32、 Φ12孔中心孔 N16 M06 T02; N19 G90 G54 G00 X0. Y0.; N20 M03 S1000; N21 G43 Z100. H02; N22 G99 G81 Z-5. R5. F100; N23 X-36. Y26.; N24 G98 X36. Y-26.; N25 G80 G91 G28 Z0. M05; / M00; 工步3：钻Φ32、 Φ12孔至Φ11.5 N27 M06 T03; N30 G90 G54 G00 X0. Y0.; N31 M03 S550; N32 G43 Z100. H03; N33 G99 G81 Z-30. R5. F110; N34 X-36. Y26.; N35 G98 X36. Y-26.; N36 G80 G91 G28 Z0. M05; / M00; 工步10：铰?12孔至尺寸 N115 M06 T09; N118 G90 G54 G00 X-36. Y26.; N119 M03 S170; N120 G43 Z100. H09; N121 G99 G82 Z-30. R5. P1000 F42; N122 G98 X36. Y-26.; N123 G80 G91 G28 Z0. M05; / M00; 工步4：扩Φ32孔至Φ30 N38 M06 T04; N41 G90 G54 G00 X0. Y0.; N42 M03 S280; N43 G43 Z100. H04; N44 G98 G81 Z-35. R5.0 F85; N45 G80 G91 G28 Z0. M05; / M00; 工步8：镗Φ32孔至Φ31.7 N9 M06 T08; N102 G90 G54 G00 X0. Y0.; N103 M03 S830; N100 G43 Z100. H08; N101 G98 G76 Z-27. R5. Q0.1 F120; N102 G80 G91 G28 Z0. M05; / M00; G76、G86的区别？ 工步11：精镗Φ32孔至尺寸 N9 M06 T10; N102 G90 G54 G00 X0. Y0.; N103 M03 S940; N100 G43 Z100. H10; N101 G98 G76 Z-27. R5. Q0.1 F75; N102 G80 G91 G28 Z0. M05; / M00; 工步5：钻3×Φ6孔至尺寸 N47 M06 T05; N50 G90 G54 G00 X40. Y0.; N51 M03 S1000; N52 G43 Z100. H05; N53 G99 G81 Z-15. R5. F220; N54 Y15.; N55 G98 Y30.; N56 G80 G91 G28 Z0. M05; / M00; 工步7：钻4×M8底孔至Φ6.8 N87 M06 T07; N88 G90 G54 G00 X23. Y0.; N91 M03 S950; N92 G43 Z100. H07; N93 G98 G81 Z-30. R5. F140; N94 X0. Y23.; N95 X-23. Y0.; N96 G98 X0. Y-23.; N97 G80 G91 G28 Z0. M05; / M00; 工步13：攻4×M8螺纹 N185 M06 T12; N187 G90 G54 G00 X23. Y0.; N188 M03 S320; N190 G43 Z100. H12; N192 G98 G84 Z-27. R10. F400; N193 X0. Y23.; N194 X-23. Y0.; N195 X0. Y-23.; N196 G80 G91 G28 Z0.; N198 G28 X0. Y0.; M30; 工步6：粗铣Φ60沉孔及沟槽 红→蓝→绿 N73 G01 X-16. Y0.; N74 Z-4.7 F1000; N75 X-61. F110; N76 X-56.5 Y-41.586; N77 X-12.213 Y-16.017; N78 X15. Y-15. F1000; N79 G03 X30. Y0. R15. F110; N80 G01 Y51.; N81 X0.; N82 Y16.; N83 G40 Y0. F1000; N84 G00 Z100. M05; N85 G91G28 Z0.; / M00; N58