- 1、本文档共123页,可阅读全部内容。
- 2、原创力文档(book118)网站文档一经付费(服务费),不意味着购买了该文档的版权,仅供个人/单位学习、研究之用,不得用于商业用途,未经授权,严禁复制、发行、汇编、翻译或者网络传播等,侵权必究。
- 3、本站所有内容均由合作方或网友上传,本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺!文档内容仅供研究参考,付费前请自行鉴别。如您付费,意味着您自己接受本站规则且自行承担风险,本站不退款、不进行额外附加服务;查看《如何避免下载的几个坑》。如果您已付费下载过本站文档,您可以点击 这里二次下载。
- 4、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等,请点击“版权申诉”(推荐),也可以打举报电话:400-050-0827(电话支持时间:9:00-18:30)。
查看更多
AWSD介绍详解.ppt
(3)Rounded discontinuities greater than a maximum size of E13, not to exceed 1/4 in [6 mm]. However, when E is greater than 2 in [50 mm], the maximum rounded indication may be 318 in [lo mm]. The minimum clearance of rounded discontinuities greater than or equal to 3/32 in [2.5 mm] to an acceptable elongated or rounded discontinuity or to an edge or end of an intersecting weld shall be three times the greatest dimension of the larger of the discontinuities being considered. 块状不连续性最大尺寸为E/3 (不超过 1/4 in. [6mm]);然而,当厚度大于2 in. [50mm]时,块状指示的最大尺寸可为3/8 in. [10mm]。块状不连续性的最小间距大于或等于3/32 in. [2.5mm]的这类不连续性,其到达另一个合格的条状或块状不连续性、或到达一条相交焊缝的边缘或端部的最小距离,必须为所考虑的较大不连续性的最大尺寸的3 倍。 (4)在一焊缝与另一焊缝或一自由边(即越过此边再无材料延伸存在)的交接处,可接受的不连续性应该符合图6.1中案例 I–IV 的限制。 (5) Isolated discontinuities such as a cluster of rounded indications, having a sum of their greatest dimensions exceeding the maximum size single discontinuity allowed in Figure 6.1. The minimum clearance to another cluster or an elongated or rounded discontinuity or to an edge or end of an intersecting weld shall be three times the greatest dimension of the larger of the discontinuities being considered. 孤立的,形似块状的一簇不连续性,其组成的每一不连续性的最大尺寸的总长超过图6.1所允许的单个最大尺寸。其到另外一簇、或到一条状或块状不连续性、或到一相交焊缝的边缘或端部的距离,必须为所考虑的不连续性中较大者最大尺寸的3 倍。 (6) The sum of individual discontinuities each having a greater dimension of less than 3132 in [2.5 mm] shall not exceed 2E13 or 318 in [I0 mm], whichever is less, in any linear 1 in [25 mm] of weld. This requirement is independent of (I), (2), and (3) above. 在任何25mm长的焊缝内,小于 2.5mm的不连续性中,每一较大尺寸的单个不连续性的总长严禁超过2E/3 或10mm(取其最小值)。本要求不受以上(1)、(2)和(3)要求的制约。 (7) In-line discontinuities, where the sum of the greatest dimensions exceeds E in any length of 6E. When the length of the weld being examined is less than 6E, the allowable sum of the greatest dimensions shall be proportionally less. 在任何6E 长度内,成一行的不连续性最大尺寸的总长超过E。当受检焊缝的长度小于6E时,容许的最大尺寸的总长必须按比例减少。 6.12.2 Discontinuity Acceptance Criteria for Cyclically Loaded Nontubular Connections. 周期载荷非管
您可能关注的文档
- ART-DECO建筑风格专题详解.ppt
- ASAP业务蓝图详解.ppt
- ASCOE气动控制阀详解.ppt
- ASCOTraining中文版系列详解.ppt
- ASIYB中国创业培训介绍TOT详解.ppt
- asme压力容器国际标准详解.ppt
- ASME第卷核动力装置设备简介详解.ppt
- asysRDSDryOven详解.ppt
- ASYS丝网印刷基础教程详解.ppt
- AS佛山赵岩详解.ppt
- 第十一章 电流和电路专题特训二 实物图与电路图的互画 教学设计 2024-2025学年鲁科版物理九年级上册.docx
- 人教版七年级上册信息技术6.3加工音频素材 教学设计.docx
- 5.1自然地理环境的整体性 说课教案 (1).docx
- 4.1 夯实法治基础 教学设计-2023-2024学年统编版九年级道德与法治上册.docx
- 3.1 光的色彩 颜色 电子教案 2023-2024学年苏科版为了八年级上学期.docx
- 小学体育与健康 四年级下册健康教育 教案.docx
- 2024-2025学年初中数学九年级下册北京课改版(2024)教学设计合集.docx
- 2024-2025学年初中科学七年级下册浙教版(2024)教学设计合集.docx
- 2024-2025学年小学信息技术(信息科技)六年级下册浙摄影版(2013)教学设计合集.docx
- 2024-2025学年小学美术二年级下册人美版(常锐伦、欧京海)教学设计合集.docx
文档评论(0)