螺栓拧紧力矩计算课程.docVIP

螺栓拧紧力矩计算书 一．相关计算参数： 螺栓规格 d mm 螺距 P mm 螺纹原始三角形高度H mm 外螺纹中径 d2 mm 外螺纹小径 d1 mm 计算直径 d3 mm 螺栓公称应力截面积As mm2 螺栓材料屈服强度 MPa 计算拧紧力矩 T Nm 计算内容： 根据要求，所需计算DN300及以上接管法兰所配螺栓拧紧力矩，故统计相关法兰如下： N1 N2 N4 N6 一效结晶器 DN1200 DN900 DN1200 DN600 二效结晶器 DN1200 DN1200 DN1200 DN600 三效结晶器 DN1200 DN1600 DN1200 DN600 APU效结晶器 DN800 DN1400 DN800 DN600 根据管法兰相关标准，DN600所配螺栓为M33 DN800、DN900、DN1200所配螺栓为M39 DN1400、DN1600所配螺栓为M45 计算过程： 螺栓规格 d d=33 螺距 P P=3.5 螺纹原始三角形高度H 外螺纹小径 d1 外螺纹中径 d2 计算直径 d3 螺栓公称应力截面积As 螺栓材料屈服强度 114 计算拧紧力矩 T 通常取计算值的0.8倍左右作为实际应用的拧紧力矩值 故 螺栓规格 d d=39 螺距 P P=4 螺纹原始三角形高度H 外螺纹小径 d1 外螺纹中径 d2 计算直径 d3 螺栓公称应力截面积As 螺栓材料屈服强度 114 计算拧紧力矩 T 通常取计算值的0.8倍左右作为实际应用的拧紧力矩值 故 螺栓规格 d d=45 螺距 P P=4.5 螺纹原始三角形高度H 外螺纹小径 d1 外螺纹中径 d2 计算直径 d3 螺栓公称应力截面积As 螺栓材料屈服强度 114 计算拧紧力矩 T 通常取计算值的0.8倍左右作为实际应用的拧紧力矩值 故 四。参考资料 《机械设计手册》第五版 第5篇Acknowledgments The authors would like to thank Johns Hopkins University for the TC-1 cells. This work was supported by a National Health Research Institutes intramural grant (IV-103-PP-22) and grants from the National Science Council, which were awarded to Y.C. Song (NSC 99-2321-B-400-004-MY3) and S.J. Liu (NSC 103-2321-B-400-008). Author Contributions Y.C.S. and S.J.L. designed the studies. Y.C.S. performed the research and analyzed the data. Y.C.S. and S.J.L. wrote the manuscript. Additional Information C57BL/6 mice were immunized subcutaneously (s.c.) once with 1 μ g of peptide mixed with or without 10 μ g of CpG adjuvant. After one week, splenocytes were harvested, and the response of IFN-γ -secreting cells was determined by ELISPOT after 48 h of peptide stimulation. Briefly, 2 × 105 splenocytes were incubated with 1 μ g