前轮毂轴承孔组合镗床设计分析.docxVIP

*********论文（设计）  PAGE \* MERGEFORMAT 48 目 录  TOC \o 1-3 \h \z \u  HYPERLINK \l _Toc420710481 摘要  PAGEREF _Toc420710481 \h 3  HYPERLINK \l _Toc420710483 Abstract  PAGEREF _Toc420710483 \h 4  HYPERLINK \l _Toc420710484 0文献综述  PAGEREF _Toc420710484 \h 5  HYPERLINK \l _Toc420710485 1 引言  PAGEREF _Toc420710485 \h 8  HYPERLINK \l _Toc420710486 1.1 MACROBUTTON AcceptAllChangesInDoc 组合机的组成及特点  PAGEREF _Toc420710486 \h 9  HYPERLINK \l _Toc420710487 1.2 MACROBUTTON AcceptAllChangesInDoc 组合机床自动线组合和分类  PAGEREF _Toc420710487 \h 9  HYPERLINK \l _Toc420710488 1.3 MACROBUTTON AcceptAllChangesInDoc 组组合机床的设计步骤  PAGEREF _Toc420710488 \h 10  HYPERLINK \l _Toc420710489 1.4 MACROBUTTON AcceptAllChangesInDoc 组合机床的通用部件的选用  PAGEREF _Toc420710489 \h 11  HYPERLINK \l _Toc420710490 2 工艺方案的拟订  PAGEREF _Toc420710490 \h 12  HYPERLINK \l _Toc420710491 2.1 MACROBUTTON AcceptAllChangesInDoc 工艺方案分析  PAGEREF _Toc420710491 \h 12  HYPERLINK \l _Toc420710492 2.2 MACROBUTTON AcceptAllChangesInDoc 加工方案的确定  PAGEREF _Toc420710492 \h 13  HYPERLINK \l _Toc420710493 2.3 MACROBUTTON AcceptAllChangesInDoc 刀具结构的选择  PAGEREF _Toc420710493 \h 16  HYPERLINK \l _Toc420710494 3 组合镗床的总体设计  PAGEREF _Toc420710494 \h 16  HYPERLINK \l _Toc420710495 3.1确定机床配置型式及结构方案应考虑的问题  PAGEREF _Toc420710495 \h 16  HYPERLINK \l _Toc420710496 3.2 MACROBUTTON AcceptAllChangesInDoc 切削用量的确定  PAGEREF _Toc420710496 \h 17  HYPERLINK \l _Toc420710497 3.3 MACROBUTTON AcceptAllChangesInDoc 切削力、切削转矩、切削功率的确定  PAGEREF _Toc420710497 \h 17  HYPERLINK \l _Toc420710498 3.4 MACROBUTTON AcceptAllChangesInDoc 被加工零件工序图  PAGEREF _Toc420710498 \h 18  HYPERLINK \l _Toc420710499 3.5 MACROBUTTON AcceptAllChangesInDoc 加工示意图  PAGEREF _Toc420710499 \h 19  HYPERLINK \l _Toc420710500 3.6 MACROBUTTON AcceptAllChangesInDoc 机床联系尺寸总图  PAGEREF _Toc420710500 \h 20  HYPERLINK \l _Toc420710501 3.7机床生产率计算卡  PAGEREF _Toc4