9发动机综合实践汇编.docxVIP

PAGE  PAGE 46 发动机综合实践 设计说明书 姓 名： 班 级： 学 号： 指导教师： 刘伟 刘建华 胡准庆 日 期： 目录  TOC \o 1-3 \h \z \u HYPERLINK \l _Toc346189870 0. 设计题目及要求  HYPERLINK \l _Toc346189874 1. 传动装置的总体设计  1HYPERLINK \l _Toc346189875 .1 传动方案的设计  HYPERLINK \l _Toc346189876 1.2 传动方案的选择  HYPERLINK \l _Toc346189879 2.齿轮的设计计算  HYPERLINK \l _Toc346189880 2.1 高速齿轮的设计  HYPERLINK \l _Toc346189881 2.2 低速齿轮的设计  HYPERLINK \l _Toc346189882 2.3圆整中心距后齿轮的校核  HYPERLINK \l _Toc346189883 3. 轴的设计计算  HYPERLINK \l _Toc346189880 3.1 轴的设计  3.1.1 中间轴的设计计算··························································· 3.1.2高速轴的设计计算 ···················································· 3.1.3低速轴的设计计算 ················································· 3.2轴的校核································································ 3.2.1 中间轴的校核····························································· 3.2.2高速轴的校核 ··················································· 3.2.3低速轴的校核····························································· HYPERLINK \l _Toc346189884 4.轴承的校核  HYPERLINK \l _Toc346189880 4.1 高速轴承的校核  4.2 低速轴承的校核···························································· HYPERLINK \l _Toc346189883 5. 润滑方式的选择  HYPERLINK \l _Toc346189880 5.1 齿轮的润滑  5.2轴承的润滑 ······························································ HYPERLINK \l _Toc346189883 6. 箱体结构尺寸的设计  HYPERLINK \l _Toc346189903 7. 设计小结  HYPERLINK \l _Toc346189904 8. 参考文献   一、设计参数 设计四冲程汽油机曲柄连杆机构，初始条件为： 1平均有效压力： QUOTE =0.8～1.2MPa； 2活塞的平均速度： QUOTE 18m/s； 3缸径和行程 6缸、缸径100mm，行程117mm 二、设计要求： 1用计算机绘制活塞装配图一张和连杆装配图一张（A4图） 2设计说明书一份，包括 （1）发动机冷却形式、曲柄半径r、汽缸工作容积、燃烧室容积 QUOTE 和汽缸总容积 QUOTE 、发动机额定转速和角速度、发动机有效功率和升功率等。 （2）每隔 QUOTE 1度曲轴转角计算活塞位移、活塞速度及活塞加速度数据，绘制曲线并进行解释 （3）根据参考文献《工程热力学》和《内燃机学》确定热力循环基本参数，每隔1度取一个曲轴转角计算P、V，作出理想p-v图并进行分析。修正最大爆发压力、点火提前角、排气提前角等数据并绘制实际p-v图。计算汽油机指示功。将热力学计算中的p-v图转化为p- QUOTE