ISO41561Straightcylindricalinvolutesplines中文翻译版201306.docxVIP

PAGE \* MERGEFORMAT iStraight cylindrical involute splines—圆柱直齿渐开线花键Metric module, side fit —米制模数 齿侧配合Part 1: 第一部分Generalities 总论翻译：朱晓峰，浙江，金华RefeReference numberISO 4156-1:2005(E)? ISO 2005译注A1：凡是带“译注XX”的，都表示翻译者的理解。译注A2：《GB/T 3478.1-2008 圆柱直齿渐开线花键》（以下简称《GB 3478.1》）译注A3：本文译者朱晓峰，毕业于桂林航天工业学院（原航专）模具设计与制造专业，已从事开发、工艺、夹具、量具十多年。曾在苏泊尔集团、浙江科惠医疗等行业内知名企业任职。并在浙江工业大学取得管理学士学位，通过美国戴克伊GDT培训。现从事汽车传动轴工作，已研究公制、英制、日本等渐开线多年，并总结了一套公式。本译文仅作参考，译者不承担相应责任。有误之错请联系本人。随本文一并翻译的还有《ANSI B92.1-1970(R1993) SAE美国渐开线花键-中文翻译完整版》。Contents TOC \o 1-3 \h \z \u HYPERLINK \l _Toc357754871 Foreword 序 PAGEREF _Toc357754871 \h v HYPERLINK \l _Toc357754872 Introduction 引言 PAGEREF _Toc357754872 \h vi HYPERLINK \l _Toc357754873 1. Scope 范围 PAGEREF _Toc357754873 \h 1 HYPERLINK \l _Toc357754874 2. Normative references 参考标准 PAGEREF _Toc357754874 \h 1 HYPERLINK \l _Toc357754875 3. Terms and definitions 术语和定义 PAGEREF _Toc357754875 \h 1 HYPERLINK \l _Toc357754876 3.1 spline joint PAGEREF _Toc357754876 \h 1 HYPERLINK \l _Toc357754877 3.2 involute spline PAGEREF _Toc357754877 \h 1 HYPERLINK \l _Toc357754878 3.3 internal spline PAGEREF _Toc357754878 \h 2 HYPERLINK \l _Toc357754879 3.4 external spline PAGEREF _Toc357754879 \h 2 HYPERLINK \l _Toc357754880 3.5 fillet PAGEREF _Toc357754880 \h 2 HYPERLINK \l _Toc357754881 3.6 fillet root spline PAGEREF _Toc357754881 \h 2 HYPERLINK \l _Toc357754882 3.7 flat root spline PAGEREF _Toc357754882 \h 2 HYPERLINK \l _Toc357754883 3.8 module PAGEREF _Toc357754883 \h 2 HYPERLINK \l _Toc357754884 3.9 pitch circle PAGEREF _Toc357754884 \h 2 HYPERLINK \l _Toc357754885 3.10 pitch diameter PAGEREF _Toc357754885 \h 2 HYPERLINK \l _Toc357754886 3.11 pitch point PAGEREF _Toc357754886 \h 2 HYPERLINK \l _Toc357754887 3.12 circular pitch PAGEREF _Toc357754887 \h 2 HYPERLINK \l _Toc357754888 3.13 pressure angle PAGEREF _Toc357754888 \h 3 HYPERLINK \l _Toc357754889 3.14 standard pressure angle PAGEREF _Toc357754889 \h 3 HYPERLINK \l _Toc357754890 3.15 base circle PAGEREF _Toc35