毕业设计（论文）-高铬铸铁高频堆焊工艺及性能的研究.docVIP

PAGE PAGE 44郑州大学毕业设计（论文）题 目：高铬铸铁高频堆焊工艺及性能的研究 Research on Property of High Chromium Cast Iron Produced with High-frequency Compounding 指导教师： XXX 职称： 教授 学生姓名： 学号： 专 业： 材料成型及控制工程 院（系）： 材料科学与工程学院 完成时间： 2008年5月 摘 要在机械零件磨损中，磨料磨损占了很大比重。采用高频感应堆焊工艺在普通碳素结构钢母材上堆焊一层2～3mm厚的高铬铸铁耐磨层，可以同时具备两种材料的优点，满足零件对韧性和耐磨性的要求。本文主要对亚共晶、共晶、过共晶高铬铸铁组织进行金相分析，并测量堆焊层的硬度 ，研究分析了不同的高铬铸铁组织与耐磨性的关系。实验得出，与亚共晶、共晶组织的高铬铸铁相比，过共晶高铬铸铁具有更好的抗磨料磨损性能。关键词：高频堆焊；高铬铸铁；耐磨 AbstractIn the mechanical parts wearing, Abrasion has been a large proportion. Wearing-resisting lay of high chromium cast iron was compounded on the low carbon steel plate with High-frequency compounding methods. At the same time that can have the advantage of two materials, meet the requirements of toughness and Wearability of parts. This article process metallographic analysis of the high chromium cast iron with different composition, and measure the hardness of surfacing, analysis the relations between different composition of high chromium cast iron and Wearability. The results show that the Hyper-ectectic high chromium cast iron have Excellent Wearability compare with thehypoeutectic and Eutectic high chromium cast iron.Keywords: High-frequency compounding ; high chromium cast iron ; wear-resist目录 TOC \o 1-3 \h \z \u HYPERLINK \l _Toc200874104 摘 要 PAGEREF _Toc200874104 \h i HYPERLINK \l _Toc200874105 Abstract PAGEREF _Toc200874105 \h ii HYPERLINK \l _Toc200874106 1 概述 PAGEREF _Toc200874106 \h 1 HYPERLINK \l _Toc200874107 1.1 研究的目的及意义 PAGEREF _Toc200874107 \h 1 HYPERLINK \l _Toc200874108 1.2 各种堆焊方法的比较 PAGEREF _Toc200874108 \h 1 HYPERLINK \l _Toc200874109 1.2.1 手工电弧堆焊 PAGEREF _Toc200874109 \h 2 HYPERLINK \l _Toc200874110 1.2.2 氧-乙炔焰堆焊 PAGEREF _Toc200874110 \h 2 HYPERLINK \l _Toc200874111 1.2.3 自动埋弧堆焊 PAGEREF _Toc200874111 \h 2 HYPERLINK \l _Toc200874112 1.2.4 气体保护电弧堆焊 PAGEREF _Toc200874112 \h 3 HYPERLINK \l _Toc20087411