- 1、本文档共5页,可阅读全部内容。
- 2、原创力文档(book118)网站文档一经付费(服务费),不意味着购买了该文档的版权,仅供个人/单位学习、研究之用,不得用于商业用途,未经授权,严禁复制、发行、汇编、翻译或者网络传播等,侵权必究。
- 3、本站所有内容均由合作方或网友上传,本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺!文档内容仅供研究参考,付费前请自行鉴别。如您付费,意味着您自己接受本站规则且自行承担风险,本站不退款、不进行额外附加服务;查看《如何避免下载的几个坑》。如果您已付费下载过本站文档,您可以点击 这里二次下载。
- 4、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等,请点击“版权申诉”(推荐),也可以打举报电话:400-050-0827(电话支持时间:9:00-18:30)。
查看更多
UL关于测试设备校准要求 -告客户通知书
尊敬的女士/先生:
从2009年1月1日开始, Underwriters Laboratories?(UL )要求涉及UL认证的测试设备的校准必须由被鉴定为合格的校准实验室完成 , 以确保实验量测结果的可追溯性. 可被接受的校准实验室是被ILAC(International Laboratory Accreditation Cooperation, 国际实验室认证联盟), APLAC( Asia Pacific Laboratory Accreditation Cooperation , 亚太实验室认证联盟) 或者EAC (European Accreditation Cooperation,欧洲实验室认证联盟) 的成员单位(比如CNAS(中国合格评定国家认可委员会)) 鉴定为合格的实验室.
此要求适用于用来测试数据或者工艺流程控制等所有涉及UL认证的测试设备.
此要求适用于UL的内部实验室,参与UL DAP ( Data Acceptance Program )计划的客户/第三方实验室及上述涉及工艺流程控制的工厂生产线.
可能对您产生的影响
UL工程师在进行现场目击测试 (包括结构检查, 选取封装样品) 之前, 会先确认要访问的实验室设备的溯源证明是否满足这一要求, 如果该实验室设备的溯源证明不能满足这一规定, UL工程师会推迟目击测试时间直至该实验室满足这一要求.
为了让您便于了解这一新的要求, 我们提供了中英文两种校准证书的范本供参考. 见附件关于校准证书的要求和中英文范例.
您可以通过以下路径了解UL对于测试设备校准的最新要求:
/global/eng/pages/offerings/services/programs/dap/tools/
每一份校准证书应按照ISO/IEC17025 的要求至少包括如下信息,除非校准
实验室有正当的理由.
1. A valid accreditation body endorsement for the calibrations performed (refer to example list of accreditation endorsements below).(实验室被授权的有效的证明(如CNAS 的Logo 和实验室编号)
2. A title (e.g. “Calibration Certificate”)(标题 (例如校准证书))
3. The name and address of the laboratory, and the location where the calibrations were carried out, if different from the address of the laboratory; (校准实验室的名称和地址, 进行校准的地点 (如果与实验室的地址不同).)
4. Unique identification of the calibration certificate (such as the serial number). Each page of supporting data requires an identification to ensure that the page is recognized as a part of the calibration certificate package. A clearly identified end of the calibration certificate package must be labeled;(校准证书的唯一性标识 (如序列号) 和每一页上的标识, 以确保能够识别该页是属于校准证书的一部分, 以及表明校准证书结束的清晰标识.)
5. The name and address of the customer;(客户的名称和地址, 一般是DAP 实验室的名称和地址.)
6. Identification of the method used;(所用方法的识别.)
7. A description of the condition of and unambiguous identification of the item(s) tested or calibrated;(校准物品的描述、状态和明确的标识 (一般为设备的制造商, 型号, 序列号等信息).)
8. The date of receipt of the calibration item(s) if this is critical to the validity and application of the re
文档评论(0)