生产车间钢结构梁吊施工方案.docVIP

张家港年产5700吨/年球形分子筛项目 生产车间 钢 结 构 吊 装 施 工 方 案 江苏南通二建集团有限公司 生产车间二层钢结构吊装施工方案 一、工程概况： 结合本工程的特点及施工方法，生产车间二层202钢结构平台上增加一个钢结构平台，以便今后电机维护及维修拆卸，平台高度为7.5米。现场设备安装都已就位，给钢梁吊装带来很大的困难，钢梁最重为1.13T。 二、 编制依据: 生产车间施工图纸 Honeywell HSE 已批准的安全方案 JGJ80—91 建筑施工起重吊装安全技术规范?JGJ276-2012?1、要求：2）选用吊带的使用吨位应大于被吊物的重量； （3）吊带表面毛刺、压痕和深的划道； 2、要求使用前应进行检查，倒链的吊钩、链条、轮轴、链盘等应无锈蚀、裂纹、损伤，传动部分应灵活正常，否则严禁使用。??起吊构件至起重链条受力后，应仔细检查，确保齿轮啮合良好，自锁装置有效后，方可继续作业。??应均匀和缓地拉动链条，并应与轮盘方向一致。不得斜向曳动，应防止跳链、掉槽、卡链现象发生。??倒链起重量或起吊构件的重量不明时，只可一人拉动链条，如一人拉不动应查明原因，严禁两人或多人一齐猛拉。?（6）齿轮部分应经常加油润滑，棘爪、棘爪弹簧和棘轮应经常检查，严防制动失灵。??倒链使用完毕后应拆卸清洗干净，并上好润滑油，装好后套上塑料罩挂好，妥善保管。? a、一人操作、一人监护；一人拉链、一人护着手链，以防脱链现象。? b、挂钩与被拉物必须钩牢、钩稳，以防脱钩。? c、操作时，严禁其它人员在作业现场作任何工作或行走，以免发生人身事故。? d、松链时，必须缓慢操作，严禁自然松链。? （11）现场动火作业时应先开具动火作业证，现场设备管道已安装好，动火时注意成品保护，动火点下方的设备管道应采用防火布覆盖，并设置接火盆。 Building industry opens up new world of entrepreneurial struggle to build a three provinces of regional central cities--in the Communist x counties the six plenary session members and comrades: today, I was commissioned by the County party Committee Standing Committee, reports to the General Assembly. Consideration of all members and alternates, and comrades attending advice. A, and this year yilai of work recalled this year yilai, in municipal of right led Xia, County solidarity led County people, to science development views for guide, to good activities for mainline, according to a city four modernizations three more of development thought, concentrated poly force, work hard, political, and economic, and culture, and social and party of construction are made has new progress, County rendering out wind fresh are, and career prosperity, and social settled, and people mind into of good situation. A facilitating the construction of the project. Firmly establish the scratch project is economic, grasping development project is to hold philosophy, to extraordinary efforts to promoting the construction of key projects. Plot 108 key projects for the year, with a total investment of 29.3 billion yuan, iron pl