[原创资料] 华模具教程NX10.0--裙边分型面做法.docVIP

[原创资料]?青华模具教程NX10.0--裙边分型面做法 裙边面分型面用途：包R边分型工件裙边面分型面要求：分型面垂直或近似垂直于胶位面，即近似法向面。 裙边面分型面优点：最大程度避免模口利角以下图为例：方法步骤：先用“等斜度曲线”抽取分型线6 l% Q2 E2 e; t0 V3 @) E, O: d5 p M1 z2 z8 Q: `( i??w1 C2 M5 D$ u角度为0 W; m, E7 x. N) @! x7 j7 T, Y! X) O; m1 h0 I7 @?$ z2 ^7 T5 Z9 O, D再对分型线进行优化：先将落差、断点接顺，再进行整体光顺在分型线上插入点集 T1 ] {2 h# V m4 y3 x @??n: q4 s8 ]8 C- d- |) {??^ V2 `4 p V再通过点重新生成封闭曲线??l0 K. X: A3 n6 H5 t0 g$ u??X7 m7 I. `; O7 d. m9 b3 |: R4 R?2 y! C2 r6 V6 w$ ~8 J?再利用”规律曲线“命令生成初步的裙边面??注意：选择”矢量“模式，以Z轴（出模方向）为矢量，角度为向外90度，抽取等参数线对曲面进行区块划分，保留光顺部份，扭曲变形部份修剪掉后重建: a) H2 w D a: W8 q6 S2 S) o3 \ @0 V* w$ n1 b2 E8 h2 P4 e4 N??A* J+ F?4 k( g+ T5 n0 K6 A- B6 U0 y7 P?- A- f* p6 ~: n h) {?3 C e- z! ^1 Q$ r??N8 d: D?( Q??n6 B$ s7 m8 a9 T( S?同样方法做出另一边$ K+ e$ j, y- U$ y G5 m. ~/ L. J# \% V- h+ c2 W缝合曲面 0 F5 Q2 y( T- T2 d3 U F4 { @5 z# g2 @??T最终效果：. f) i??g# w w0 R# x. g? ? 青华提供UG模具设计，产品设计 CNC编程 PROE产品设计 PowerMill编程等课程培训 如有需要请加我QQ：2936668579 联系电话0769华陶静老师 加我QQ或找我电话可赠送UG下载视频教程 be limited to no more than 2 days of work, material deposited in special insulated containers, material handling to gently and make use of thermal insulation material in windproof, waterproof, moisture-proof measure. 6.2 thermal design optimization for high-temperature special thermal insulation for piping support and hanger design, reduced heat dissipation of the hangers, ensure that the wall does not overheat. Small-diameter piping, thermal instrument layout and positioning of support and hanger design take fully into account the expansion space and insulation thickness. Large-diameter pipes after heat preservation plastering construction of valves, turbine, checking smooth surface, high temperature powder paint fully dry after. Protective coverings for electric equipment insulation boards designed with pressure plate, when ordering according to the installation diagram, model specifications publishing order, ensure when installing corners neat, uniform appea