渐开线齿廓是生齿轮的关键.docVIP

渐开线齿廓是生成齿轮的关键，在这里介绍利用参数化设计的方法生成渐开线齿廓的方法 首先建立齿轮的几个重要参数： 模数 m 齿数 z 压力角 a 分度圆半径 r 基圆半径 rb 齿根圆半径 rf 齿顶圆半径 ra 关系：r=(m*z)/2, rb=r*cosa, rf=r-(ha+c)*m, ra=r+ha*m, 标准齿轮的ha=1，c=0.25. 1、打开零件设计模块，点击图标，打开参数设计窗口，如图 将齿轮的参数输入进去，需要公式的利用添加公式图标建立公式，结果如图： 建立好参数后，点击应用后点击确定图标。 2、建立变量为x的y1和y2的参数方程，点击图标，弹出窗口如图所示： 输入y1= rb*sin(t*PI*1rad)-rb*t*PI*cos(t*PI*1rad),结果如图： 打开第二个窗口后，输入y2=(rb*cos(t*PI*1rad))+((rb*t*PI)*sin(t*PI*1rad)),如图： 3、利用前面建立好的参数，画出分度圆，基圆，齿根圆，齿顶圆，然后给x赋一系列的值，就可以得到渐开线上一系列的点，用样条曲线连接，就得到了渐开线，然后利用修剪，倒角等命令就可以得到渐开线齿廓了。 Evaluate括号中为x的值。 连接好的渐开线如图： 修剪好的渐开线齿廓： 再利用圆形阵列得到整个齿轮的渐开线齿廓： 设计圆锥减速器重要的是对大圆锥齿轮和小圆锥齿轮的设计，下面介绍设计锥齿轮的方法。 根据所给参数，先把齿轮的毛坯画出来，如图： 2根据分锥角、根锥角和顶锥角，找到当量分度圆所在的平面和当量分度圆，当量齿顶圆，当量齿根圆，当量基圆 integrated energy, chemicals and textile Yibin city, are the three core pillars of the industry. In 2014, the wuliangye brand value to 73.58 billion yuan, the citys liquor industry slip to stabilise. Promoting deep development of integrated energy, advanced equipment manufacturing industry, changning district, shale gas production capacity reached 277 million cubic metres, built the countrys first independent high-yield wells and pipelines in the first section, the lead in factory production and supply to the population. 2.1-3 GDP growth figure 2.1-4 Yibin, Yibin city, Yibin city, fiscal revenue growth 2.1.4 topography terrain overall is Southwest, North-Eastern State. Low mountains and hills in the city landscape as the main ridge-and-Valley, pingba small fragmented nature picture for water and the second land of the seven hills. 236 meters to 2000 meters above sea level in the city, low mountain, 46.6% hills 45.3%, pingba only 8.1%. 2.1.5 development of Yibin landscapes and distinctive feature in the center of the city, with limitations, and spatial structure of typical zonal group, 2012-cities in building with an area of about 76.2km2. From city-building situation, old town-the South Bank Center construction is lagging behind, disintegrat