PLC步进顺控令的应用2.docxVIP

PLC步进顺控指令的应用-2发布: 2009-2-17 10:33?|??作者: wuguosheng?|查看: 104次500)this.width=500500)this.width=500 border=0　这是十字路口交通信号灯的控制题，我已做过了，以前用的编程方法是启保停的方式。如果说采用启停方法设计出梯形图，用时一天好象不太过份。而采用步进顺控方式来编程，其用时若超过2小时好象就感到笨了（下面的梯形图只用了一个小时）。时间短，指令长点，好象没什么大关系？加上我还没看到用顺控指令编的，于是进行了偿试，结果很成功。下面是我具体的做法：500)this.width=500500)this.width=500 border=0按上表可以看出东西方向、南北方向的灯是可以进行分别控制的。按这样的思路做下去。不然光那些东、西、南、北的用语就先撑昏了？500)this.width=500500)this.width=500 border=0先确定I/O分配如上表所示。500)this.width=500500)this.width=500 border=0做出顺序功能图如上图所示。该功能图的含意是：一打开PLC，特殊继电器M8002即产生一脉冲，将状态元件S0置于初时步。与M8002并列的X001为外部SB2控制，在每一次停机时均对状态元件从S10----S34进行区间复位，同时它可起停止的作用。此时外部SB1给X000一个信号，步S10被激活，S10一被激活，同时也激活了东西向的步S20和南北向的步S30。也就是说此时分二路走。现先由东西向的步S20开始，S20一被激活, 绿灯Y000即被点亮，25S后，T0动作将步转入S21。S21一被激活Y000被再次点亮，此时的Y000是执行的是3S的闪光定时及闪光。3S时间一到，T1又将步转入S22, S22一被激活，黄灯Y001被点亮，2S后T2动作将步转入S23，即红灯被点亮，30S后T3将步转入S24进入等待状态。而南北向过程与东西向的过程基本相似不进行分析。而南北向的步进入步S34时与东西向的步S24汇合同时激活步S10进行循环。根据功能图很方便地编出以下梯形图：500)this.width=500500)this.width=500 border=0The rectification measures: (LED Leadership: Luo Mingjun, rectification time: before September 25th, 1, long-term adherence) to solve the problem of lack of awareness of the harm of Party cadres the four winds. To further strengthen education and guidance on the implementation of the central eight provisions, the provincial nine provisions of the county committee of the ten provisions extensive publicity, eliminate thoughtBarriersThe rectification measures: (LED Leadership: Luo Mingjun, rectification time: before September 25th, 1, long-term adherence) to solve the problem of lack of awareness of the harm of Party cadres the four winds. To further strengthen education and guidance on the implementation of the central eight provisions, the provincial nine provisions of the county committee of the ten provisions extensive publicity, eliminate thoughtBarriersThe rectification measures: (LED Leadership: Luo Mingjun, rectification time: before September 25th, 1, long-term adherence) to solve the problem of lack of awareness