英文翻译原文-切削刃的几何形状,工件的硬度的影响,进给速度和切削速度对表面粗糙度和力量完成硬化AISI H13钢的车削.docVIP

 英文翻译原文-切削刃的几何形状,工件的硬度的影响,进给速度和切削速度对表面粗糙度和力量完成硬化AISI H13钢的车削.doc

  1. 1、本文档共21页,可阅读全部内容。
  2. 2、原创力文档(book118)网站文档一经付费(服务费),不意味着购买了该文档的版权,仅供个人/单位学习、研究之用,不得用于商业用途,未经授权,严禁复制、发行、汇编、翻译或者网络传播等,侵权必究。
  3. 3、本站所有内容均由合作方或网友上传,本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺!文档内容仅供研究参考,付费前请自行鉴别。如您付费,意味着您自己接受本站规则且自行承担风险,本站不退款、不进行额外附加服务;查看《如何避免下载的几个坑》。如果您已付费下载过本站文档,您可以点击 这里二次下载
  4. 4、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等,请点击“版权申诉”(推荐),也可以打举报电话:400-050-0827(电话支持时间:9:00-18:30)。
  5. 5、该文档为VIP文档,如果想要下载,成为VIP会员后,下载免费。
  6. 6、成为VIP后,下载本文档将扣除1次下载权益。下载后,不支持退款、换文档。如有疑问请联系我们
  7. 7、成为VIP后,您将拥有八大权益,权益包括:VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
  8. 8、VIP文档为合作方或网友上传,每下载1次, 网站将根据用户上传文档的质量评分、类型等,对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档
查看更多
 英文翻译原文-切削刃的几何形状,工件的硬度的影响,进给速度和切削速度对表面粗糙度和力量完成硬化AISI H13钢的车削

编号: 毕业设计(论文)外文翻译 (原文) 学 院: 国防生学院 专 业:机械设计制造及其自动化 学生姓名: 郑 波 学 号: 1000110532 指导教师单位: 机电工程学院 姓 名: 郭中玲 职 称: 高级工程师 2014年 1 月 12 日 EFFECTS OF CUTTING EDGE GEOMETRY,WORKPIECE HARDNESS, FEED RATE AND CUTTING SPEED ON SURFACE ROUGHNESS AND FORCES IN FINISH TURNING OF HARDENED AISI H13 STEEL Tugrul ?zel, Tsu-Kong Hsu, Erol Zeren Department of Industrial and Systems Engineering Rutgers, The State University of New Jersey, New Jersey 08854 USA Abstract In this study, effects of cutting edge geometry, workpiece hardness, feed rate and cutting speed on surface roughness and resultant forces in the finish hard turning of AISI H13 steel were experimentally investigated. Cubic boron nitrite inserts with two distinct edge preparations and through-hardened AISI H-13 steel bars were used. Four factor (hardness, edge geometry, feed rate and cutting speed)- two level fractional experiments were conducted and statistical analysis of variance was performed. During hard turning experiments, three components of tool forces and roughness of the machined surface were measured. This study shows that the effects of workpiece hardness, cutting edge geometry, feed rate and cutting speed on surface roughness are statistically significant. The effects of two-factor interactions of the edge geometry and the workpiece hardness, the edge geometry and the feed rate, and the cutting speed and feed rate are also appeared to be important. Especially, small edge radius and lower workpiece surface hardness resulted in better surface roughness. Cutting edge geometry, workpiece hardness and cutting speed are found to be affecting force components. The lower workpiece surface hardness and small edge radius resulted in lower tangential and radial forces. 1. INTRODUCTION Hard turning, machining ferrous metal parts that are hardened usually between 45-70 H

文档评论(0)

pab547 + 关注
实名认证
文档贡献者

该用户很懒,什么也没介绍

1亿VIP精品文档

相关文档