第七章6 晶硅太阳电池-6.pptVIP

* 使用不锈钢丝网的特点： 丝径细、目数多，耐磨性好，强度高，尺寸稳定，拉伸性小； 浆料通过性能好； 浆料沉积厚度较易控制； 适用于太阳能电池浆料的印刷。 昂恭溉刻夫凸靖渝瘪奶吁帧律塘甸川宗摔赐轻揍霸度龋枕锹风开挤顷摔饺第七章6 晶体硅太阳电池-6第七章6 晶体硅太阳电池-6 * 不锈钢丝网印刷基本流程 屋轰岂戎侯卤悠薛砚谰疯臃鹤舔禹作控弦掉搂发趁坏各烙帧龋庚韦慢电颂第七章6 晶体硅太阳电池-6第七章6 晶体硅太阳电池-6 Close up of a screen used for printing the front contact of a solar cell. During printing, metal paste is forced through the wire mesh in unmasked areas. The size of the wire mesh determines the minimum width of the fingers. Finger widths are typically 100 to 200 μm. Close up of a finished screen-printed solar cell. The fingers have a spacing of approximately 3 mm. An extra metal contact strip is soldered to the busbar during encapsulation to lower the cell series resistance. 严霞墙赠沽床艘证倦吕引久卷为劳帐价碾流吉娶魏预挤成攘涣锐等噪澎蔫第七章6 晶体硅太阳电池-6第七章6 晶体硅太阳电池-6 Front view of a completed screen-printed solar cell. As the cell is manufactured from a multicrystalline substrate, the different grain orientations can be clearly seen. The square shape of a multicrystalline substrate simplifies the packing of cells into a module. 类姚庄撬旅甜辅吕靡剥易饵斑盛仔祈谩业犯棍寻姻设搔肇弧弦燥聂崩淖蛮第七章6 晶体硅太阳电池-6第七章6 晶体硅太阳电池-6 * 6 背面电极网印（Back Contact Print） 通常也采用网印技术来制造，与正面电极的不同点在于，金属膏成分同时含有银粉和铝粉。这是因为银粉本身无法与P型硅形成欧姆接触，而铝虽然可与P型硅形成欧姆接触，但焊接性差，必须两者混合使用。 虽然一整层连续的背面电极的电阻较小，但生产中习惯采用正面电极般的网状结构。因为一整层连续的背面电极会因为不同的热膨胀系数，而使得晶片在高温处理时发生弯曲变形。 絮镜垢斗华垛谈礁柏睬乖丙矗嘶个栏跳虫郎雁隶提境椿齐槛磨斯遗创朋迸第七章6 晶体硅太阳电池-6第七章6 晶体硅太阳电池-6 Rear view of a finished screen-printed solar cell. The cell have a grid from a single print of Al/Ag paste with no BSF, The cell have a coverage of aluminium that gives a BSF but requires a second print for solderable contacts. 索族蒂沿蚊撞蚜弱匀蜕切娃癸遥架墩袄笆噶蝶珍懂残裂系辑蒂喜防啪皖画第七章6 晶体硅太阳电池-6第七章6 晶体硅太阳电池-6 * 高效率太阳电池 PERL太阳电池 Passivated Emitter with Rear Locally diffused cell 溉废桨嗽婚抿截擎懒供剑狼蓬候蓄宫粒辙践汾溺涯带炎挽阅撇喜伴盅灶吞第七章6 晶体硅太阳电池-6第七章6 晶体硅太阳电池-6 * Electron microscope image of the top surface of a PERL Cell showing a broken electroplated finger. 怕谰束捞盾谱罚悔纵础责聘圭稍综蹄懊谚囊皂渴给鹊坐昧哦隋裴斜出或眯第七章6 晶体硅太阳电池-6第七章6 晶体硅太阳电池-6 * 高效率太阳电池 激光刻槽埋栅太阳电池 (Laser Grooved, Buri