《日处理60000吨印染废水处理工艺设计毕业设计》.doc

摘 要本设计中，污水处理规模为日处理生产废水000m3/d，进水水质：COD为0mg/L，BOD为0mg/L , SS为0mg/L，色度为0度。出水水质达到《纺织染整工业水污染物排放标准》（DB 32/670-2004）中规定的排放的要求，即COD≤10mg/L，BOD≤mg/L，SS≤0mg/L，色度≤0度。 印染废水具有色度高，COD、BOD含量高，成分复杂，水质、水量变化剧烈等特点。因为印染废水属于难降解的废水，所以本设计采用水解酸化提高废水的可生化性。经过方案比选，本设计采用水解酸化- 接触氧化- 混凝工艺，其处理效果明显优于传统工艺，对BOD、COD、SS有很好的处理效果，并具有能耗低、产泥量少的特点，且剩使废水达标排放。 关键词：印染废水 水解酸化 生物接触氧化 混凝沉淀 Abstract In this design, the scale of sewage treatment is to dispose wastewater 000m3 / d, water quality: COD 240mg / L ,BOD80mg / L, SS 100mg / L, the color is 100 degrees, Water quality can meet the emissions requirements specified in the textile industry standards for water pollutants (DB 32/670-2004), that of COD ≤ 180 mg / L of BOD ≤40mg / L, SS ≤ 100mg / L, and chroma ≤ 80 degrees. High color printing and dyeing wastewater, the COD, high content of BOD, complex composition, water quality and quantity of rapid change and so on. Dyeing wastewater is biodegradable wastewater, so the design uses a hydrolysis acidification to improve the wastewater biodegradability. After the program than the election, this design uses a hydrolysis acidification - contact oxidation - coagulation process, the treatment effect was better than the traditional process, BOD, COD, the SS has a good treatment effect, and has low energy consumption, sludge production is less features, and excess sludge can be dehydration. Set after coagulation and sedimentation, sedimentation tanks, as a tertiary treatment, to obtain better water quality, wastewater discharge standards. Keywords: printing and dyeing wastewater ; hydrolysis acidification ; biological oxidation ; coagulation and sedimentation 撤消修改目 录 摘 要 1 Abstract21课程设计的主要内容和基本要求51.1 工程设计资料51.2 设计任务51.3 基本要求61.4 参考文献61.5课程设计图纸内容及张数62 污水处理方案设计2.1 规模与处理程度的确定 7 2.2 污水处理方案的确定 8 3 污水处理厂工艺设计 12 3.1 污水处理构筑物的设计 12 3.2 污泥处理系统设计 19 4 污水处理厂总体布置 20 4.1 平面布置及总平面图 20 4.2 各构筑物高程布置 23 5 厂区概况 24 5.1 厂区污水 24 5.2 噪声 24 5.3 固体废弃物 246 安全生产和消防设施 247 结论及建议 25 第二篇 设计计算书 26 1 设计资料 26 1.1 设计题目和任务 26 1.2 设计进出水水质及处理