2015命令汇总.docVIP

基本配置命令 交换机 交换机命名[router]sysname 修改Super密码[router]super password mima [router-e0/1]duplex{half/auto/full}双工状态 [router-e0/1]speed{10/100/auto}工作速率 [router-e0/1]flow-control端口流控 [router-e0/1]MDI{across/auto/normal} 端口MDI/MDIX状态 [router]vlan id 创建VLAN [router]undo vlan id 删除VLAN [router-vlan3]port e0/1 to e0/4连续端口 [router-e0/1]port access vlan 3加入指定VLAN [router-e0/1]port link-type {trunk/access/hybrid}设置工作模式 [router-e0/1]port trunk permit vlan {ID/ALL}设置trunk端口允许通过的VLAN [router-e0/1]port trunk pvid vlan 3设置trunk 端口的PVID 交换机S3026的端口聚合 [router]link-aggregation port-num1 to port-num2 {ingress/both}ingress接口入方向 both接口出入方向 [router]undo link-aggregation{master-port-num/all}master接口聚合主接口号(最小的 以太网物理接口)清除端口聚合 STP基本设置 [router]stp enable打开STP 默认是关闭状态 [router-e0/1] stp disable 关闭一个端口的STP 路由器的基本配置 routersystem-view用户视图 [router]系统视图 启动FTP:[router]ftp-server enable [router]local-user tt设置FTP用户名 [router-luser-tt]service-type ftp设置服务类型 [router-luser-tt]password simple tt设置密码 PPP协议的基本配置 PAP的验证方配置 [router-s0/1]ppp authentication-mode pap [router]local-user huawei对端路由器名字 [router-luser-huawei]password simple huawei [router-luser-huawei]service-type ppp PAP的被验证方配置 [huawei-s0/1]ppp pap local-user huawei password simple huawei 本地路由器名字 CHAP的配置 CHAP的主验证方配置 [router]local-user huawei对端路由器名字 [router-luser-huawei]password simple huawei [router-luser-huawei]service-type ppp [router-s0/1]ppp authentication-mode chap [router-s0/1]ppp chap user router本地路由器名字 CHAP的被验证方配置 [huawei-s0/1]ppp chap user huawei 本地路由器名字 [huawei-s0/1]ppp chap password{simple/cipher} huawei MultiLink PPP的配置 (一)虚拟接口模板配置 [router]local-user huawei对端路由器名字 [router-luser-huawei]password simple huawei [router-luser-huawei]service-type ppp [router]interface virtual-template 1 [route-virtual-template1]ip add 配置串口CHAP验证 [router-s0/1]link-protocol ppp [router-s0/1]ppp authentication-mode chap [router-s0/1]ppp chap user router本地路由器名字 [router-s0/1]ppp chap pass simple huawei [router-s0/1]ppp mp virtual-template