特殊关键过程控制记录单面数搭接焊.docVIP

特殊/关键过程监控记录 单位工程名称： 控制内容：1、单面搭接焊焊接作业指导书已编制，审批手续齐全； 2、部位： 3、钢筋焊接规格：C25 4、已做书面技术交底 质量要求： 1、Ⅲ级钢的单面焊搭接长度要大于或等于10d； 2、搭接时，钢筋应预弯，以保证两钢筋的轴线在同一轴线上； 3、钢筋接头的焊缝厚度h应不小于0.3d，焊缝宽度不小于0.7d； 检查结果： 1、检查焊工证件，证件合格有效，焊工：，证号： 2、C25焊头：289个，取一组做拉伸试验，见试验报告单： 3、对单面搭接焊焊接接头逐个进行帮条长度检查，检查结果如下： C25： 330mm,290mm,345mm,315mm,325mm,295mm,305mm,280mm,290mm,340mm 335mm,320mm,295mm,310mm,320mm,340mm,285mm,350mm,315mm,300mm 315mm,345mm,320mm,290mm,280mm,320mm,285mm,340mm,330mm,325mm 345mm,330mm,290mm,355mm,315mm,295mm,270mm,305mm,310mm,325mm 290mm,335mm,320mm,345mm,310mm,285mm,325mm,315mm,340mm,330mm 记录人： 日 期： 特殊/关键过程监控记录 单位工程名称： 检查结果： C25： 325mm,340mm,330mm,285mm,300mm,320mm,285mm,335mm,330mm,320mm 315mm,325mm,295mm,305mm,270mm,335mm,310mm,345mm,330mm,290mm 300mm,315mm,345mm,305mm,345mm,295mm,295mm,335mm,325mm,280mm 290mm,330mm,325mm,305mm,300mm,345mm,340mm,285mm,325mm,310mm 285mm,270mm,325mm,300mm,340mm,290mm,330mm,310mm,335mm,350mm 345mm,320mm,315mm,325mm,295mm,290mm,305mm,280mm,310mm,340mm 310mm,320mm,340mm,285mm,350mm,295mm,270mm,305mm,310mm,325mm 310mm,320mm,340mm,285mm,350mm,345mm,330mm,290mm,355mm,315mm 285mm,325mm,325mm,295mm,305mm,270mm,315mm,340mm,330mm,350mm 320mm,285mm,335mm,330mm,340mm,285mm,350mm, 315mm,345mm,305mm 330mm,290mm,355mm,315mm,295mm,305mm,300mm,345mm,340mm,325mm 340mm,290mm,330mm,310mm,335mm,295mm,315mm,320mm,340mm,320mm 350mm,295mm,270mm,305mm,310mm,325mm,325mm,295mm,305mm, 320mm 记录人： 日 期： 特殊/关键过程监控记录 单位工程名称： 检查结果： C25： 335mm,340mm,335mm,285mm,310mm,320mm,285mm,345mm,330mm,325mm 295mm,325mm,285mm,305mm,275mm,335mm,310mm,345mm,345mm,290mm 325mm,325mm,295mm,305mm,270mm,300mm,340mm,290mm,330mm,310mm 315mm,325mm,295mm,305mm,270mm,335mm,355mm,315mm,295mm,325mm 275mm,325mm,300mm,340mm,290mm,330mm,310mm,335mm,295mm,315