一些仿真.docVIP

uchar code tab[]={0x3f,0x06,0x5b,0x4f,0x66,0x6d,0x7d, 0x07, 0x7f,0x6f,0x77,0x7c,0x39,0x5e,0x79,0x71}; P0=0XFF;//关掉数码管的位选信号。阻止数码管受到P0口信号的影响。 delay_1ms(1); wela=1; delay_1ms(1); wela=0; dula=0; P0 = sled_disp_buff[i+count]; /*显示数字 i*/ dula=1; dula=0; #includereg52.h sbit dula=P2^6; sbit wela=P2^7; unsigned char x;//存储计数变量 unsigned int m; display(); unsigned char code tab[]= {0xc0,0xf9,0xa4,0xb0,0x99,0x92,0x82,0xf8,0x80,0x90}; void delay() {for(m=0;m3600;m++);} void dispaly(unsigned char date) { P0=0xff; Wala=1; Wela=0; delay(); P0=tab[date/10]; dula=1; dula=0; P0=0xfe; wela=1; wela=0; delay(); P0=tab[date%10]; dula=1; dula=0; P0=0xfd; wela=1; wela=0; delay();} void main() {EA=1; EX0=1;//外中断TO IT0=1;//选择负跳变触发中断 x=0; while(1) {display(x); }} void int0() interrupt 0 {x++; if(x==100) x =0} #includereg52.h #include intrins.h sbit dula=P2^6; sbit wela=P2^7; unsigned char count; void delay(unsigned char x) {unsigned char m; while(x--) {for(m=0;m250;m++) }} void mian() {count=0; unsigned char i,j; unsigned char code tab[]={0xfe,0xfd,0xfb,0xf7,0xef, 0xdf,0xbf,0x7f}; unsigned char code port[]={0x3f,0x06,0x5b,0x4f,0x66,0x6d,0x7d, 0x07,0x7f,0x6f,0x77,0x7c,0x39,0x5e,0x79,0x71};} while(1){ for(j=0;j100;j++) {for(i=0;i6;i++) { P0=0xff; delay(); wela=1; delay(); wela=0; delay(); dula=0; P0=port[count]; dula=1; dula=0; wela=0; P0=tab[i]; delay(); count++;} if(count==16;) count=0; delay();}} #includereg52.h #include intrins.h #define uchar unsigned char #define uint unsigned int sbit dula=P2^6; sbit wela=P2^7; uchar count; uchar k; uchar i; uchar g; void delay_1ms(uchar x) {while(x--) {for(i=0;i150;i++) {;} }} void mian() {uchar code tab[]={0xfe,0xfd,0xfb,0xf7 ,0xef,0xdf,0xbf,0x7f}; uchar code port[]={0x3f,0x06,0x5b,0x4f,0x66,0x6d,0x7d, 0x07,0x7f,0x6f,0x77,0x7c,0x39,0x5e,0x79,0x7}; while(1) {for(g=0;g100;g++) {for(k=0;k6;k++) {P0=0xff; delay_1ms(1); wela=1; wela=0; dula=0; P0=port[count+i]; dula=1; dula=0; wela=1; P0=tab[i]; wela=1; wela=0; delay_1ms(1); } count++; if(co