《ansys耦合和约束方程教程.ppt

16.2.10 约束方程练习-涡轮叶片(续) 10. 存储并退出 ANSYS: Pick the “QUIT” button in the Toolbar 选择 “Save Everything” 选择[OK] 或使用命令: SAVE FINISH /EXIT,ALL Evaluation only. Created with Aspose.Slides for .NET 3.5 Client Profile 5.2.0.0. Copyright 2004-2011 Aspose Pty Ltd. 16.2.11 约束方程练习-摆杆刚性区 说明 用“刚性区” (约束方程)替代摆杆右边2/3模型. 刚性摆杆 (EX = 2.11e6 kgf/cm2), 右端施有500 kgf 的竖向力作用(在 X=33 cm处). 注释: 1 kgf = 9.81 N, 1 kgf/cm2 = 98066.5 Pa Evaluation only. Created with Aspose.Slides for .NET 3.5 Client Profile 5.2.0.0. Copyright 2004-2011 Aspose Pty Ltd. 16.2.11 约束方程练习-摆杆刚性区(续) 载荷和材料特性 Evaluation only. Created with Aspose.Slides for .NET 3.5 Client Profile 5.2.0.0. Copyright 2004-2011 Aspose Pty Ltd. 16.2.11 约束方程练习-摆杆刚性区(续) 1. 用“swaybar-cerig”作为作业名，进入 ANSYS。 2. 读入文件 “swaybar1.inp”: Utility Menu File Read Input from … 或使用命令: /INP,swaybar1,inp Evaluation only. Created with Aspose.Slides for .NET 3.5 Client Profile 5.2.0.0. Copyright 2004-2011 Aspose Pty Ltd. 16.2.11 约束方程练习-摆杆刚性区(续) 3. 在X=33, Y=0, Z=0 处定义节点(节点号为 8000) : Main Menu Preprocessor -Modeling- Create Nodes 或使用命令: N,8000,33 Evaluation only. Created with Aspose.Slides for .NET 3.5 Client Profile 5.2.0.0. Copyright 2004-2011 Aspose Pty Ltd. 16.2.11 约束方程练习-摆杆刚性区(续) 4. 设置单元类型为 2 并在8000号节点上建立 MASS21 单元: Main Menu Preprocessor -Attributes- Define Default Attribs ... Main Menu Preprocessor -Modeling- Create Elements -Auto Numbered- Thru Nodes + 或使用命令: TYPE,2 E,8000 Evaluation only. Created with Aspose.Slides for .NET 3.5 Client Profile 5.2.0.0. Copyright 2004-2011 Aspose Pty Ltd. 16.2.9 耦合练习-叶轮叶片(续) 载荷和材料特性 Evaluation only. Created with Aspose.Slides for .NET 3.5 Client Profile 5.2.0.0. Copyright 2004-2011 Aspose Pty Ltd. 16.2.9 耦合练习-叶轮叶片(续) 1. 按教师指定的工作目录，用“cp-blade”作为作业名，进入 ANSYS。 2. 恢复“cp-blade.db1”数据库文件: Utility Menu File Resume from … 或使用命令: RESUME,cp-blade,db1 Evaluation only. Created with Aspose.Slides for .NET 3.5 Client Profile 5.2.0.0. Copyright 2004-2011 Aspose Pty Ltd. 16.2.9 耦合练习-叶轮叶片(续) 3. 进入前处理器，分别定义单元类型1为SOLID95, 单元类型2为MESH2