- 1、本文档共6页,可阅读全部内容。
- 2、原创力文档(book118)网站文档一经付费(服务费),不意味着购买了该文档的版权,仅供个人/单位学习、研究之用,不得用于商业用途,未经授权,严禁复制、发行、汇编、翻译或者网络传播等,侵权必究。
- 3、本站所有内容均由合作方或网友上传,本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺!文档内容仅供研究参考,付费前请自行鉴别。如您付费,意味着您自己接受本站规则且自行承担风险,本站不退款、不进行额外附加服务;查看《如何避免下载的几个坑》。如果您已付费下载过本站文档,您可以点击 这里二次下载。
- 4、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等,请点击“版权申诉”(推荐),也可以打举报电话:400-050-0827(电话支持时间:9:00-18:30)。
查看更多
MIMOAdaptiveProcessControlinStampinMIMOAdaptiveProcessControlinStampin
MIMO Adaptive Process Control in Stamping Using Punch Force
By Yongseob Lim
In stamping, both manufacturing and control engineers have faced challenges to prevent stamped parts from wrinkling and tearing, to improve their dimensional accuracy (e.g., to minimize springback), and to maintain consistency in the stamping process (e.g., reduce variations in stamped part quality). In this research, a process control strategy is introduced in sheet metal stamping to improve the quality of stamped parts and the consistency of the stamping process.
Sheet metal stamping is a primary manufacturing process for large-volume highspeed and low-cost production of components, such as panels in automobiles and home- appliances. A stamped part is made by placing a sheet of metal (the blank) between an upper die (or punch) and a lower die,which are geometric negatives of each other, and then stamping the sheet of metal using a press. A blank holder, or binder, is used to hold the edges of the sheet of metal,and to control the flow of material into the die, sometimes using drawbeads, which provide additional restraining forces on the blank. Once die design and validation are accomplished, high productivity is the hallmark of stamping operations due to their suitability for large-volume production. As shown in Figure 1.1,1, a punch (i.e., upper die) is forced towards the lower die, with the material to be drawnplaced in between. In Figure 1.1.1, Fp is the punch force,ls is the material draw-in, h is the punch stroke, and Fb is the binder (or blank holder) force. Traditionally, stamping presses have been mechanical in design, but modern presses are often electro-hydraulic. Presses also typically have rubber, springs, and pneumatic/hydraulic pistons to passively cushion the die in a stamping press from the punch impact.
Figure 1.1.1: Schematic of the sheet metal stamping process including process varia
您可能关注的文档
最近下载
- 作文草稿纸模板.docx VIP
- 税务局2023年税务执法资格模拟考试题及答案.doc VIP
- 商用车行业月报-货车行业:8月内需偏淡,出口景气维持,以旧换新效果有望逐月显现-240922-方正证券-17页.pdf VIP
- 工程电磁场与电磁波答案(丁君).pdf
- SNT 0370.2-2021出口危险货物包装检验规程第2部分性能检验.pdf
- 江苏省淮安市2024届高三上学期第一次月考历史试题及答案解析.docx
- 部编版一年级上册语文《四季》第一课时课件.ppt
- 2021新译林版高二英语选择性必修二第二单元课文原文及单词表(word可编辑).docx
- 中药学(张廷模).doc
- 幼儿园中班语言秋天的颜色.ppt VIP
文档评论(0)