DS12C887电子时钟(附程序)..docVIP

下面附有实物图和引脚接法图及程序 时钟实物图 LCD1602引脚连接 P1.0 P1.1 P1.2 P0.0~P0.7 DS12C887引脚连接(打叉的表示不接) 蜂鸣器引脚连接 按键引脚连接 P1.3 P3.4 P3.5 P3.6 P3.7 源程序 #includereg52.h #includeintrins.h #define uint unsigned int #define uchar unsigned char sbit lcdrs=P1^0; sbit rw=P1^1; sbit lcden=P1^2; sbit s1=P3^4; //功能键 sbit s2=P3^5; //增大键 sbit s3=P3^6; //减小键 sbit s4=P3^7; //闹铃查看键 sbit beep=P1^3;//蜂鸣器 sbit dscs=P1^7; sbit dsas=P1^6; sbit dsrw=P1^5; sbit dsds=P1^4; sbit dsirq=P3^3; //中断 bit flag1,flag_ri;//定义标志位 flag1设置闹铃 uchar count,s1num,flag,t0_num; char miao,shi,fen,year,month,day,week,amiao,afen,ashi; char code table[]= 20 - - ; // 20 - - uchar code table1[]= : : ; // : : void write_ds(uchar,uchar); uchar read_ds(uchar);void set_time(); void read_alarm();void set_alarm(uchar,uchar,uchar); void delayms(uint z) //延时毫秒的程序 { uint x,y; for(x=z;x0;x--) for(y=112;y0;y--); } void di() { beep=0; delayms(100); beep=1; } void write_cmd(uchar cmd) { lcden=0; lcdrs=0; P0=cmd; _nop_(); lcden=1; delayms(1); lcden=0; _nop_(); } void write_dat(uchar dat) { lcden=0; lcdrs=1; P0=dat; _nop_(); lcden=1; delayms(1); lcden=0; _nop_(); } void lcdint() { lcden=0; write_cmd(0x38); // 显示模式设置 write_cmd(0x0c); //开显示，不显示光标，不闪烁 write_cmd(0x06); //写一个字符后地址加1，屏幕不移 write_cmd(0x01); //清屏 delayms(1); } void init() { uchar num; rw=0; EA=1;//开总中断 EX1=1;//开外部中断1 IT1=1;//外部中断下降沿触发 flag1=0; t0_num=0;s1num=0;week=1; /* write_ds(0x0A,0x20);//打开振荡器 write_ds(0x0B,0x26);//设置24小时模式，数据二进制格式，开启闹铃中断 set_time();//设置上电默认时间,调试的时候用 */ lcdint(); write_cmd(0x80); for(num=0;num15;num++) { write_dat(table[num]); } write_cmd(0xc0); for(num=0;num11;num++) { write_dat(table1[num]); } } void write_sfm(uchar add,char date) //写时间,2位一起写 { char shi,ge; shi=date/10;ge=date%10; write_cmd(0xc0+add); write_dat(0x30+sh