- 1、本文档被系统程序自动判定探测到侵权嫌疑,本站暂时做下架处理。
- 2、如果您确认为侵权,可联系本站左侧在线QQ客服请求删除。我们会保证在24小时内做出处理,应急电话:400-050-0827。
- 3、此文档由网友上传,因疑似侵权的原因,本站不提供该文档下载,只提供部分内容试读。如果您是出版社/作者,看到后可认领文档,您也可以联系本站进行批量认领。
查看更多
SYD-267石油产品开口闪点与燃点试验器.
SYD-267石油产品开口
闪点与燃点试验器
目 录
一、用途………………………………………………………2
二、主要技术指标和参数……………………………………2
三、仪器结构…………………………………………………2
四、仪器使用及注意事项……………………………………3
五、仪器成套及技术文件……………………………………3
本仪器为精密、低温制冷仪器,
使用前请详阅说明书,谨慎操作!
一、产品简介??? SYD-267石油产品开口闪点与燃点试验器是按照国家标准GB/T267《石油产品闪点与燃点测定法(开口杯法)》和国家石油化工行业标准SH/T0318《开口闪点测定器技术条件》所规定的要求。测定润滑油及深色石油产品的闪点和燃点。二、技术指标??? ★工作电源: AC 220V±10%,50Hz。??? ★外坩埚 :⑴ 材料:0.3优质炭素结构钢,表面镀黑;⑵ 上口内径:Φ100±5毫米;⑶ 高:50±5毫米;⑷ 底部内径:Φ56±2毫米。??? ★内坩埚:⑴ 材料:0.3优质炭素结构钢,表面镀黑;⑵ 上口内径:Φ64±1毫米;⑶ 高:47±1毫米;⑷ 底部内径:38±1毫米;⑸ 刻度线:在距上口边缘12毫米及18毫米处各有刻线一条。??? ★气体导管:喷口直径Φ0.8~Φ1毫米 ,内孔表面光洁能使火焰调节3~4毫米。??? ★加热器:电炉加热,加热功率1000W可调。??? ★温度计:0~360℃,分度1℃,技术条件符合石油产品试验用液体温度计技术条件GB/T514的规定。??? ★环境温度:≤35℃。??? ★相对湿度:≤85%。??? ★整机功耗:不大于1100W。三、仪器成套??? ★SYD-267 开口闪点试验器主机??? ★内坩埚??? ★外坩埚??? ★引火器??? ★温度计0~360℃??? ★温度计夹(立柱)??? ★电源线(250V 6A)??? ★保险丝 5A(Ф5×20)
One, product introduction
SYD-267open flash point of petroleum products and the ignition tester in accordance with the national standard GB / T267 petroleum products - Determination of flash point and ignition point ( open cup method ) and the National Petroleum and chemical industry standard SH / T0318 open flash point measuring device technical conditions requirements. Determination of lubricating oil and dark petroleum products - Determination of flash and fire points.
Two, technical indicators
Of working power: AC220V + 10%,50Hz.
In the outer crucible: the material:0.3high quality carbon structure steel, surface plating black; the upper opening diameter:100 dia + 5mm; the high:50 +5 mm; the bottom diameter:56 +2 mm dia.
In the inner crucible: the material:0.3high quality carbon structure steel, surface plating black; the upper opening diameter:64 dia + 1mm; the high:47 +1 mm; the bottom diameter:38+ / - 1mm; the scale line: from the upper edge of a 12 mm and18 mm respectively have reticle a.
In the gas conduit: nozzle diameter lower than 0.8~1mm in diameter, inner hole smooth surface can make the fl
文档评论(0)